Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi All,
We have been developing device with pca10028 evaluation board and in the process we use also few other custom boards with nrf51822. We use IAR. The device system...
Is there any recommended value for PSTORAGE_MIN_BLOCK_SIZE or is it completely system determined. The commends in pstorage_platform.h are somewhat unclear.
If I only require...
Hello.
I want to migrate function of "sd_ble_gatts_value_set" to nRF52 from nRF51.
I use nRF52832 ,S132 and PCA10040.
I saw documentations about the function.
infocenter...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I want to go to nrf_drv_uart_uninit(); right after sending data.
in order to save current consumption.
So I made source code...
Hi.
I'm using nRF51822, SDK10.0.0, S130.
Hex files : Soft device, Application, bootloader.
I want to download at once.
How can I combine Hex files to make them 1 file...
I'm trying to piece together how to be able to get this migration to work OTA via DFU. I was told by Nordic that all you need is to .zip SD8 + Boot(SDK10) and DFU both to...
I'm using:
nRF51422
SDK 7.1.0
Softdevice S310 2.0.1
nrfjprog.exe v 8.3.0
JLinkARM.dll v 5.10m
If I use the Segger with nrfjprog.exe to upload the softdevice...
I am a bit confused about what happens to ACK_PLD when ack payload packets are lost. I am assuming that in case of ack payload packet loss MAX_RT bit in STATUS is set.
...
Hello,
i have a nRF51 DK 1 and the Dongle to test and try some BLE applications.
Now i want to test how long does it take to establish and close a simple connection.
...
Hello,everyone,I encountered a confusing problem.
My device is nrf51822. I want to test whether the communication between two equipments is normal . So I choose one as central...
I am using a nrf51822 based tag and Android official SDK to implement my custom app. I perform the following steps:
1. Scan
2. Connect
3. Discover services
4. Write...
What CRC type is used for the crc calculation with the function
uint16_t crc16_compute (const uint8_t * p_data, uint32_t size, const uint16_t * p_crc )
of the nRf52 SDK...
Hi
I have a prototype of a board that uses a nNF52832 to communicate over Bluetooth, the board has some buttons intended for user input.
As the board size is little...
Hello!
I am sorry to ask a simple question that why my device can't program the ".hex" file about the demo of ble_app_hrs_rscs_relay_s130_pca10028 after I have already program...
Hi,
I have Wifi MCU connected to nr51822.
I download the binary file from a Cloud and need to transfer it via UART, so i need a C code of the nRF5x Programing tool....
