Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
What is the switching frequency of the DC/DC regulator in the nRF52832? The DC/DC is great for reducing power consumption, but I am worried about the switching noise getting...
Hello.
I am trying to save i/o lines on an 8-pin PIC, and planning to run an nRF24L01P with its CE pin tied to VDD. I am willing to power-down to get out of the RX mode...
Hi
I am using an Identive NFC reader/writer SCL3711 and their sample app to read tags.
In the sample app, through the debugger I can see that it is registering an NDEF...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use nrf51422 and integrated BMA250E for Pedometer,
Now I can count the step but I dont how to calculate the speed, cadence and stride length like below
static void...
Hi All,
From my firmware I need to send large ble packets say of 1 K to the phone.
Is there any library or example code for sending large packets. Currently I am splitting...
Hi,
Our application requires that we connect a nRF52832 to a Microchip PIC32MZ host via the Nordic parts UART (RS-232 at CMOS levels).
In a previous application, we...
Hi everyone,
I've been testing SPIM with easyDMA, using nrf_drv_spi. I'd like to flush a 6-axis sensor FIFO in one SPI operation (31 samples * 12 bytes = 372 bytes) but...
Hi,
I am working with the ble_app_uart (central and peripheral) example and they already run fine. Now I discovered that some button actions are already defined on the...
Hello,
I have created the simple software usign NRF51DK to make the led blink for 5 times by using while loop
just to make the other part of my software
my aim of this...
hi，i have a question.
i set the advertise type to BLE_GAP_ADV_TYPE_ADV_NONCONN_IND MODE, and i add scan response data,but i can't see scan response data.Why?
Hi,
I would like to connect nrf8001 to a Renesas microcontroller but I could not find any documentation on how to proceed with this step. The only documentation I could...
The ADC module requires that the output impedance of the connected voltage source be 1kohm or less (section 31.1.3 of RM).
Does the same restriction apply for the LPCOMP...
