I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi All,
Am using NRF52 ,S132 soft device , I am trying to send two packet of twenty byte every 5s . in a timer interrupt handler I call ble_nus_string_send twice continuosly...
I have following set up for current measurement.
NRF52 DK PCA10040 v0.9.0
nRF5 SDK v11.0.0 : Power Profiling Application
S132 SoftDevice v2.0.0
nFR Master Control...
hi
does my nrf51422 v2 have uart over ble?
its version 2 and its supported sdk is 6 and it does not have ble_nus.c
does my nr51422 v2 support uart over ble?
Hello,
I've been playing with BLE applications with my custom board with nRF52832.
I have flashed "flash_s132_nrf52_2.0.0-7.alpha_softdevice" from ble_app_template project...
Hi
I'm having issues implementing ADC sampling to my ble project.
I'm using the nRF51-DK with SDK11 and S130. I used the example from github ( github.com/.../adc-example...
I want to update over BLE with using DFU tool. But do not start updating process.
DFU tool indicates "Enabling DFU Bootloader".
Bootloader stops at memcpy() of dfu_ble_peer_data_set...
Hi there,
I am now in FCC stage and finalizing a FCC code using the radio test sample code. I do have a delimma on what type of radio mode I have to use. Will you please...
Hi,
I am working on a school project, and I need to use a nRF51 dongle as a BLE master. However, when I try to use JLinkExe to connect to the dongle, it fails all the time...
Hi am using NRF52 board ...and am trying to send data(which is not a string) using ble_bus_string_send . I send data only once from a one second timer but the other side is...
Hi all!
I'm working on an nrf51822 (technically right now I'm using the PTR5518 as I'm still prototpying), and trying to set up a voltage divider on my pcb in order to...
Hi,I am debuging my programm base on SD-110-V6.0.0 ,sdk-V5.2.0. When I use the
static void characteristic_disc_req_send(const ble_ans_c_t * p_ans, const ble_gattc_handle_range_t...
Hi everyone,
I have a nrf51-dk. I am running Master Control Panel app on my win7 computer. However, I cannot see my nrf51-dk in discovered devices section. Log says, Loading...
I am working on an application for the nRF52 Preview board, using SDK 0.9.2. I need to acquire about five analog samples from a single channel at roughly 100 Hz, then wait...
I use SDK9.0,SD8.0,the device is 51822AC,the device can enter to Bootloader mode.
As it shows below.
Then I selected the .zip file to start DFU
But when it reached...
I'm trying to do all my development on linux, mostly so that I can use a continuous integration environment. I'm setting up a server to compile my firmware app on every pull...
