Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
A good problem to have... we're only seeing 300nA current draw with a 3V lithium primary while in SystemOFF on the nRF51822, using LDO.
Is that correct? We've measured...
HI , ALL
i added a event in the function 'on_ble_evt' like followings:
case BLE_GAP_EVT_ADV_REPORT:
printf("Start Advertising\r\n");
break;
At first i think...
Hi, I mostly use the SDK 7.2 or SDK 10 and S110 7.1 or 8.0
since I have multiple custom boards that uses revision 2 and 3 chips.
My custom board I'm about to use has...
I want get an interrupt from the ADC after every sample (oversampled by 4, so burst is enabled). This works fine with EasyDMA, but I want to be able to not use the EasyDMA...
Is there some documentation somewhere to explain how these work?
I kinda understand but in app_timer, why use a software interrupt of the same priority as the RTC interrupt...
In my project, the nrf51422 chip will be hosted on a board with another CPU. I need to be able to flash the firmware through the SWD interface, controlled by the host CPU...
Hello,
I have a running system powered by ARM Cortex-M3 (LPC1343 MCU) and I want to add bluetooth through nRF51822 usb dongle.
I want to send some data from LPC1343...
Hi,
I try to send a string using example code ble_app_uart_pca10028 without input from terminal
,but directly from inside the code
All of the tutorials I've search...
hello there i want to interface adxl345 with nrf51822 using SPI interface i am new to spi. i am using spi master with spi slave example. i want to write 0x08 in 0x32 register...
I want to debug RF51822 board by uart port , communicate with pc, e.g use printf() in program,after download RF51822 board,print statement to pc uart port, how to realize...
I am trying to use my nRF52-DK with Yggdrasil.
I took example from here: *\nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral\ble_connectivity\pca10040\ser_s132_uart...
Hi, I was able to successfully implement the tutorial titled "Testing and using a simple BLE application" available in the Tutorial section and transfer data from termite...
Using OBS-421 from Connectblue as Central. Using simple AT command to connect and get data. Can connect successfully with Cypress BLE as well as the TI sensortag and get data...
Hello,
When i have a bootloader installed and i try to debug application, it doesn't start application probably because debugger programmed application without the right...
