Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hello:
Im rewritting a program from ST32F105RC to NRF51822.
In a part of the program of ST32, it checks if the interruption from pins 5-9 (EXTI9_5_IRQn) is enabled, and...
Hi,
I worked with temp sensor example and sofdevice s110 and something stuck on some function.
Anyway, I made readout from registers but softdevice blocks register access...
My nRF51 will occasionally lose connection to the computer, and I have to disconnect and then reconnect it before it will work. How can I reset the device dynamically, without...
I'm trying to compile a project I have for nrf51 on nrf52. I am running into errors with macros not being set.
For example:
error: #20: identifier "ADC_CONFIG_RES_10bit...
Hi,
I'm working on a sensor application that sends out fairly large quantities of data via BLE notifications. I understand how bluetooth works and have read and followed...
Hi,
I'm currently testing ble_app_uart on nRF51822 custom board. I connected it to nrf51 DK P19 and was able to program the hex file successfully.
But it doesn't run...
Hi, In your documentation you specify the maximum CPU temperature 85 DegC.
What problems could one expect after this point?
How much safety margain du you have on this number...
I'be been reading over and over the datasheet but cannot see how to dissable Enhanced ShockBurst features for my application which only requires basic one way radio.
I...
Hello,
I'm trying to program that module, but i can't do it correctly.
I'm using a program that works fine in nrf51 DK, but when I program this in ptr5518 my smartphone...
I want to port either the S210 experimental DFU over ANT_FS to serial DFU or the S110 dual bank serial DFU project to be S210 compatible.
I'm using S210 V4 and SDK 8
...
I would like to connect more than 8 devices to a single host. Therefore I would have to set the same role to multiple devices.
What are the implications of using the same...
HI,
I have some problems with the function sd_ble_gap_scan_stop(). I want to stop scanning into the RTC1 event handler but when I use this function (sd_ble_gap_scan_stop...
HI:
i have a question.if i use 51822 to connect other ble(ti or csr) ,could that be achieved.i have used ti dongle to scan 51822,but can't found 51822 device.if 51822 connect...
Hello,
In our project we use HID service. The difference between our HID and standart HID is that we use our own UUIDs. Our report charactestics include Report Refernces...
