Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi there,
After prototyping a device with modules and on a breadboard, I transitioned to a custom PCB with nRF24L01+, matching network from the spec sheet, and 2.45 GHz...
Hi everyone
now i used softdevice s120 scan and connect two s110 device
and i used sd_ble_gap_rssi_start() when connect event ,
then get the rssi in BLE_GAP_EVT_RSSI_CHANGED...
HI,all!
Recently my nrf51822 device encountered a tough issue,the detials are:
My device connected to an android app, which has some bugs about ble connection so the...
HI,
I am using sdk 8 and pca10028 dk. I follow following procedure,
Program the softdevice using nrfgo
Program the test_bootloader using nrfgo
Program the application...
I have some questions about how I will use this structure ,first of all I know that The "data" member of the ble_gatts_evt_write_t is meant as a placeholder for the address...
I am trying to create a windows app that will read data from an accerometer via a nrF8001 ble module.are there any example i can see for communication between windows and...
Hi, Nordic Engineers. Now, i use a external 32mhz crystal on my board. i have add code"NRF_CLCOK->XTALFREQ = 0X00", but the BLE radio seems not work. Led flick is ok.
Why...
Hi Guys,
I have a SITECOM Bluetooth Dongle connected to my PC and I want to receive data from nRF51 DK via bluetooth (for example heart rate monitor data).
Could someone...
Hi everyone,
I must to comunicate from HW to PC with SPP over BLE. So I took the dongle BLED112 (side PC) and the HW where is mounted a nrf51822 like uart BLE interface....
Hi,
the product specification of the nRF51822 states the possibility to carry quadrature demodulator
signals on GPIO pins.
This would let one allow to observe the physical...
Hi,
I am a newbie to nrf, I am trying to understand the lbs example while running on nrf dev board. I want to set my application as follows:
Blinking LED while advertising...
Hi, I have a problem with the HFCLKSTARTED interrupt.
I can't have it. (I'm a little bit pressed with time I have to send a document in 2 days, so if you can quick respond...
We are currently using SoftDevice 5.2.1 and was given the task to migrate to 6.2.1. I doing so, I placed 6.2.1 hex onto our device and turned it on. Yikes, many errors. Most...
