I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I am able to build my project, but when I try to flash it to the board via ninja flash_<target> I can select the device in nrfjprog.py, I know, that I have to use "'0'" as...
I am attempting to add a UART to interface to an external MCU. I have the uart example running (without any RTT info) yet when I port the uart code to the ble-thread example...
Is it possible or there is support in nrf52840 such that I can enable readback protection from the firmware itself?
I found an APPROTECT register in bitfields. But how to...
Hello,
I have one custom board which have Nordic's nrf52840 chip. I'm using this chip to scan the surrounding beacons.
For beacon scanning i have integrated Bluez stack...
Dear All,
I tried to take the Capp sense example and implement it in my beacon app which was based on the beacon app example. I am using nrf52382 and sdk16 , segger version...
Hello,
I'm working on nrf52832 dfu secure bootloader example.I implemented button less example to update my firmware and it works fine.
Now i switch off the power supply...
HI , I used NRF52832 SDK15.3,examples:ble_app_ancs_c.When i testing ANCS,I deleted the pm_handler_secure_on_connection(p_ble_evt) in the ble_evt_handler function, The BLE...
Hi All,
I have one custom board based on IMX6UL on which i'm using Nordic's nrf52840 chip.
I'm using zephyr's hci_uart sample application on nrf52840 for beacon scanning...
Hi all,
Greetings of the day.
Here I am not able to flash the code which is built with IAR platform. We tried loading the IAR based blinky example project from the SDK...
Hi all,
Greetings of the day.
Here I am not able to flash the code which is built with IAR platform. We tried loading the IAR based blinky example project from the SDK...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
How do i use a single serial port to communicate with the server...
NRF52840 development board does not have any programs when burning into bootloader and application and protocol stack and settings.hex,
Why do you need an OTA to enter the...
The questions are related to nrf9160:
How much memory space is currently used and free on the Thingy:91, nrf9160?
How much memory would take a complex timing routine...
I'm working nrf52832 , SDK V15.3.0 and S132. I have implemented whitelist in application and its working fine. I need to add one phone as master device so i need to hard coded...
Hello,
I'm using nRF52811 SoC with nRF5_SDK16.0.0 and SoftDevice v7.0.1. I'm using following code to write data into flash. This code is tested with nRF52840 in both debug...
