I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Dear support team,
Channel survey (RSSI report for each data channels) are now available on S132v6. However, for users who need to use v4.0.2, is there alternative method...
I am using the Hackable Kit from Electronut labs and using their Bumpy , black magic probe alternative for programming. I would like to control a servo motor precisely at...
My code is on the multi-link example and it works well when I use another nrf52dk board as the "Nordic_Blinky" peripheral device, but it can't find my other BLE device.
...
Hello
I am running gls example on SDK14.2.
I paired after flashing program to my DK board, and then turn off power.
And turned on again, but i can't connect to my DK...
HI. I used a translator.
I am using the RNG example of SKD15.
I know that when I set the range of the random number to 1 byte, the number from 0 to 255 is generated. ...
I am using a Raspberry PI as a 6LoWPAN router, running Raspbian 9.4. Linux 4.14.34. Radvd 2.15.
I configured everything as described in IoT User Guide . I am using Miredo...
Hi,
As well know, the nrf51822 can only work either TX or RX mode at the same time.
Normally, the nrf51822 device is working in RX mode (by using function "nrf_esb_start_rx...
Hello, i'm trying to updade my firmaware using the DFU. I manage to do it with nRF Connect and nrfutil but i'm trying to a custom central to flash the software without any...
Dear all,
I am using an adafruit-nrf52-pro-feather (nrf52832) to run my project of detecting voice by this below scenario:
++ Setting up:
[PC] ==== USB cable ====...
To learn how to use FDS, I started by importing the code from the flash_fds example. My application is using peer manager and I got really strange errors until I realized...
Hello!
I am trying to set up the interface between an ARM Cortex-M4 andthe nRF8001. After RESET I see following data on the MISO line:
(turquoise=REQN/CS - pink=MOSI ...
Hi,
I would like to control the LEDs based on the PTM 215B switch by programming it using nRF52 DK. Where each button in the switch should turn one LED.
I am using...
Hi, Nordic.
I'm developing multiple peripheral and a central. Central is only scanning and Peripherals are only advertising.
I got Adv data and Scan rsp data successfully...
Hi,
I work on a ANT proximity search project using SDK12.2.0 and softdevice S332v2.0.1 on nRF52832.
I have a ANT sensor which is 5cm apart from the Nordic 52832. And the...
Hi there,
Can you please tell if with 'Sniffer' I can track down and see all images shared with my pc's webcam?
If so, how can i do that?
Thank you so much for your...
