Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Question about usage. I am using the nRF52, and ported product code that was running on the Alpha SDK11 to the release SDK11. I believe that what I will describe is a new...
According to the product specification of the nRF51422 the current between the advertisements is:
i_sleep = I_on + I_rtc + I_x32k
16k Ram enabled: = 2,6 µA + 0,1 µA...
I realize that this code is "experimental", but we are trying to utilize it as a reference and having problems with its stability and scan results.
Specifically, we are...
Hi!
We are currently implementing a time synchronization algorithm using a nRF52s. Currently, we´re getting the min error of 20ms between synchronized slaves. We think that...
I'm using a nRF51 with 32K RAM and SD120. When I started using RTT Viewer I could send data to the terminal, and debug my code. Recently my J-Link plus won't allow me to debug...
I'm trying to secure my peripheral by allowing only bonded devices to connect. I'm using device manager, when I bond a central with nrf master control, the bonding succeed...
Hi,
I'm facing the following issue when trying to use the DFU bootloader. Below you can find the code of the bootloader, which I flash after I erase everything, flash S110...
hii....
i want to make my device connected through a secret pass code (may be six digit)..ie. my device get advertise then when master control panel discover my device...
Hello,
I was just wondering what are the steps to download my software that I made to nRF51422 to the nRF51822. I changed the target device and the memory areas in the...
Hi,
I am using SD 120 9.1.0 and SDK 8 as a central and SD 110 V8.0.0 and SDK 8 as a peripheral.
I have a setup central connects with 8 peripherals. First I had 1 central...
Hi guys,
I'm wondering what is written there in "empty section" between 0x7c0 and 0x1000 address? Are there any special registers (which must not be overwritten)? It looks...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello everyone,
I want to know if it is possible and how to show advertising data on display lcd (20x4 or graphic lcd). I'm using PCA10028 board with S120 and Nokia5110 LCD...
Hello,
I have read through the pstorage documentation here: devzone.nordicsemi.com/.../a00018.html
and I followed the tutorial here:
devzone.nordicsemi.com/.../
...
I created a bsp folder dfu_dual_bank_serial_s120 from PCA10028/dfu_dual_bak_serial_s13 in examples/dfu/bootloader/PCA10028.
This is for supporting DFU over UART for our...
