I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am using " BLE-Gateway " example from nRF51-ble-bcast-mesh to advertise my custom "Manufacturer Data" from 1 nRF51422 device to another nRF51422.
I've made the...
I have been able to implement the PER test (on nRF51822) using the direct_test_mode_s110 and code based off the example python code from the nAN34 zip file. I adjusted to...
Hi,
I want write a demon running on linux to control the 51822 dongle to connect or disconnect with mobile phones.
Now I have one idea, which is using string as command...
Hello,
I need to send packets that are larger than 20 bytes to once characteristic with a variable length. When I set the variable length to 100 bytes, the Attribute table...
NRF51822 supply voltage is 3V battery. When I design principle diagram, I have a question.
Both AVDD and VCC_nRF are connect with the battery's positive?
While trying to get the SDK's bootloader working with gcc, I have to replace some ARMCC-speific code found in bootloader_util_arm.c:
__asm void StartApplication(uint32_t...
I am using the nRF51-DK and have Timer1 setup as follows:
void start_timer(void)
{
NRF_TIMER1->MODE = TIMER_MODE_MODE_Timer;
NRF_TIMER1->TASKS_CLEAR = 1;
NRF_TIMER1...
Hi Guys,
I am currently using the ble driver for windows (Python) to get notifications from two Gatt services (Same Service/charac/descriptors/etc basically same application...
I've just trying to get SPI working, everything is compiling OK but when initialising the SPI, when the line below is hit,
/* Clear waiting interrupts and events */
p_spi_instance...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
I would like to support app_button, however I need to configure a pin as NOPULL and trigger on a low to high transition without debouncing.
I don't see a way this can co...
HI,
We survey APPLE's ANCS right now! But we have a question that need your help.
I use ios device ios 8.3,ble softdevice 8.0
I have some questions about the pairing...
Hi,
I tryed to compile code for DFU from GitHub, but every time some file is missing, then I must search it on net, then download for 100 times!!! When I thought I finished...
