Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi there,
When i disconnect the keyboard, the nrf51822 will restart advertising in directed mode.
And then on_adv_evt() will receive BLE_ADV_EVT_PEER_ADDR_REQUEST event...
Hi,
I want to use BLE for following situation and I wonder if it is achievable.
I have a 3 boards with nrf51822. Two of these boards have mpu6050 sensors connected to nrf51822...
Hi,
I am a little confuse at the moment and wondering if anyone would have any insight on the matter.
I am making a pair of device with s110 and s120. So the s120 will...
Hi,
I'm trying to write my own application based on the ble_lbs example on nrf51822. Recently I've discovered a problem with reconnection to the beacon. I can successfully...
So, we have been developing our firmware (for a while now) against a SoftDevice version called 6.0.0-1 alpha. We are getting close to production time, so we wanted to switch...
I had a product working with S110(BLE peripheral).
I am trying to get same BLE feature working on an product working with S210(ANT)
So I chose S310 to have both ANT and...
Hi devzone...
My setup is nrf51422 dk with soft-device S110 on the server side and on the client side i am running MCP 3.8.0 on a PC using usb dongle.
I am using Queued...
1 sensor per nRF51288.
Sensor supports either 400kHz I2C (10k pull up recommended) or SPI (2MHz typ, Max 20 MHz)
From the nRF51288 Product Specification:
Run current...
I want to use the s130 softdevice because we need the broadcaster/observer mode at the same time. I bought the nRF51 Dongle and the beacon Device.I use the Keil IDE, debugging...
From the question "Advertising on a single channel", the new S110 supports advertising on one single channel. What I want to know is if S120 supports listening on one single...
Hi,
Thank you for looking into this issue.
The target BLE module we are using is a custom board (Rigado BMD200) based on nRF51822 s110 chip. We have tried a few example...
Hi,
I am following the tutorial using Raspberry Pi Kernel version 3.18, but after the step 7, the raspberry gets frozen with the colorful image in the beginning of the boot...
Hello,
we want to establish a UART communication between the Dynastream N548M8CB Module and a TI Mikrocontroller. I have tested the UART loopback example with the pca10028...
In the data sheet of SHT21 is this the formula to calculate the temperature:
T = -46.85 + 175.72 * temp_data / 2^16
temp_data has the value 26'464.
The result should...
Hi,
I'm trying to define a new service, and on the GAP settings, I would like to advertise my service, but I get an error message: advertisement packet too long.
What...
