Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I run a basic code on nRF52832 and measure the power consumption of the chip (using DVM). The current consumption is 400 uA which is a lot just for a single timer in my application...
The tutorial is a huge help. I've been working on this for some days now, and it looks like I'm almost there. But just one last hurdle (I hope). The title pretty much says...
Hi Nordic Support,
I am trying to use BLE DFU. But for the first step I can not find the example that
is mentioned at this link: https://infocenter.nordicsemi.com/index...
Hi,
I'm working on sending string data over mesh by following this case , my message is printed on server side in mesh_msg_handle() function (access.c file), but I want...
Hello guys I'm using windows (10) using parallels in a virtual machine in mac (high sierra), all in its latest version.
The board is a PCA10040 V1.1.0. with the bootloader...
I program SD132 into nrf52832 and then program bootloader secure into nrf52832. on nRFToolbox is show name " DFUTARG" I'm using nRFToolbox for OTA. When OTA process is successful...
Hellou, I am developing apllication mesh application from example light switch. In application program i receive data from mesh and this data is stored to external serial...
I am looking for the third party nrf 52832 BLE module in which i need following configurations,
Size is less then 9mm*9mm
Chip antenna or PCB antenna
GPIO pins atleast...
Hi!
I would like to completely isolate the nRF52840 on the Preview-DK (2017.32) on hardware level.
Scenario
I would like to power the nRF IC with the external supply...
Hello, I'm new to Nordic boards.I would like to measure the bit error rate for a BLE link using nRF52840.
Is there any way of modifying any of the existing examples to add...
We use iOS nRF Connect primarily for DFU updates and find a real annoying issue with its behavior. We see this problem behavior on both v1.8.5 and v1.8.2, on both iPhone and...
Dear All,
Brief about the requirement:
ToF (Time of Flight) value computed is inclusive of the overhead delay of notifying to the application layer in the BLE stack...
Is it possible to use app_timer with the mesh stack?
Up to now I was not able to integrate the app_timer library into my build.
Can you give me an example how to integrate...
Hello Everyone,
I'd like to know if it is possible to use nfc to collect bonding informations from a smartphone. Then I'd like to transmit these informations to other devices...
Hi, i'm using nRF52 DK to communicate CX93510 encoder chip via SPI. I'm using nrf_drv_spi library with SPI0 connected to pins:
#define CX93510_MISO_PIN 22 #define CX93510_MOSI_PIN...
