i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
51822/S130/SDK v12
I was testing prepared Write from iOS to 51822. Write Req/CMD can succeed, but Prepared Write failed with 'Unknown error code 0x82'.
What this 0x82...
I am design a very compact board for my project and running out of space. For this I am planning to replace two DCDC inductors with a single one. Is it possible to do this...
I am communicating with the nrf8001 via SPI, from an HCS08 MCU. First thing I receive:
0x01 0x04 0x81 0x02 0x00 0x02
This makes sense, it tells me it is in setup state...
In my design I am planning to power up some sensors from nRF52832 GPIOs. Is it possible to maintain the GPIO state high during the low power mode of MCU?
Please guide here...
Hello,
I have been testing the BLE multilink examples for the s120 softdevice. More specifically, I have tested the ble_app_hrs_c example in the experimental s120 folder...
Is it possible to configure the parameters of the advertising library (eg. SDK v12.3.0 using SD130 v2.0.1) so that my peripheral device (eg. nRF51) changes after a limited...
I've configured peripheral for broadcast, but why can't IPHONE search it? I don't need APP development. I just want the phone to show it. Is there any special requirement...
Hi,
I was considering the following scenario and didn't find an answer. Could you please help?
Assumption:
There in a BLE peripheral (e.g. nRF52) and central ...
Im using sdk 14.0 and s132 When i add flashwrite codes to my project which has bluetooth communication ,it does not work I wanna send data to flash and i wanna read/write...
I do not want to use SoftDevice, I want to write new application from application to Code Area(0x00 - 0x80000).
Can I use fds without using SoftDevice?
Also, Is there...
Hello,
I am using SDK 12.2.0 with s130_nrf51_2.0.1 softdevice and running ble_app_hrs example.
My FLASH and RAM settings are:
FLASH (rx) : ORIGIN = 0x1b000, LENGTH...
Hello,
I am using sdk12.2.2 and pca10040. I want that my beacon advertises continuously for 10 sec and then it stops advertising for 5 secs. Do I need to use rtc for this...
As i am migrating to 52 and tuning the ble app, i realized by reading many posts here that:
external HF xtal is not recommended
external LF xtal can be replaced by...
Hi Nordic,
I am trying to implement DFU-OTA in beacon. For that I am trying to make beacon connectable. My requirement is to work the beacon in non-connectable mode during...
Im try to read the RPD register, but always get the same value RPD=0
uint8_t channel=0;
int index;
hal_nrf_set_operation_mode(HAL_NRF_PRX);
hal_nrf_set_power_mode(HAL_NRF_PWR_UP...
