I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
First attempt at implementing buttonless dfu; assistance would be greatly appreciated. Using SDK v11 + s130 + nRF51822.
Please note that iphone screen captures supporting...
Hello,
I am still having troubles with the BLE_GATTC_EVT_TIMEOUT. The problem is that the error is not happening frequently and is hard to reproduce. It is also hard to...
I was building my own custom application that connects a nrf_drv_timer to an ADC start trigger using PPI on an nRF51822 and I could not get it to work. I asked a previous...
Hi
I have ported a simple function from nRF51 to nRF52 which Outputs PWM coded Startup Diagnose Information via a GPIO.
The Timing is generated by wait Loops and GPIO will...
I am using the nRF Connect Tool, everything is working fine (Y)
My question is related with the Log file, is there any way to get in the Log File only the data sent through...
Hi,
I am new to nrf52 series and I have just started playing with NRF52 series Development kit. I am working on a project that requires the functionality of both ANT and...
Hello! I know there're a lot of questions about program custom board.
I try to programm my board used onboard j-link (p19 socket)
I can't pass the first step - can't force...
Hi. I've developed a custom board on an old E0 51422 chip with SDK 6.1 and SD110 7.3.0. Everything works fine with that setup (SPI, interrupts, timers, etc).
Got new batch...
I have a project (using a Ble Nano) that currently is running on Nordic SDK 8.1 but I want to update it to 12.2 . I currently use terminal to compile the project (I got the...
I am using Segger for Mac. I followed the tutorial on importing a Nordic example from the Nordic SDK 12.0 examples folder. It is the UART BLE Peripheral Example.
I got...
Hi all, I'm working on secure bootloader SDk12, I made the required changes to work button less dfu now it jumping from application to bootloader but it needs write 0x01 manually...
The program is hanged when I use below code to set Manufacturing specific data (I am using SDK12.0.0 S130) Please comments.
uint16_t DataSize = 14;
uint8_t MfgSpecData...
Hello,
I would like to implement a precise timer which calculates/counts the time in microseconds which I can use for
calculating the time elapsed between parts of the...
Hi!
Does anyone run UARTE with EasyDMA enabled? I don't want to use interrupts and simply copy every received UARTE bytes to global tx_buffer....and pooling with amount...
