I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
The MCP server requires authentication. To complete the setup, you'll need to: 1. Get an API key from Nordic Semiconductor / Kapa.ai 2. Reconfigure the server with the auth...
Hi All,
My leds on the custom board wont get recognized. Keep getting this error.
A bit of strack trace:
Device tree:
I think I am missing something...
Hi,
We're coming to the end of prototyping a project on the Thingy91X and are fine-tuning the power management. We have been able to implement a simple demo on the nrf9151dk...
Hi Support Team,
Our product is based on nrf5340 and ncs V2.5.2. I developed a Windows application(based on .NET8.0 and Windows SDK11) to provision and configure the system...
Hi, I'm struggling to setup an application on the nrf54l15dk to control the nrf9151dk SLM over UART.
I have done the Cellular IoT Course and successfully controlled the...
I'm trying out the GNSS sample for the nRF9161 DK. I am trying to enable minimal assistance, but I get an error message with error code 65536: *** Booting nRF Connect SDK...
Hi,
Can MCUboot be used as a second stage bootloader (an application from the Secure DFU Bootloader over Serial Link standpoint) to be DFU'ed to existing devices which now...
Is it possible for users to regenerate the nRF9160 GNSS factory almanac data from public sources?
https://github.com/nrfconnect/sdk-nrf/blob/main/samples/cellular/gnss...
Hel lo, I am us ing a custom nRF5 2832-based b oard that has no DCDC circu itry (LDO onl y). What happened in NCS v2 .5.1
After power-on, the system did not st art (e...
Hello,
I am trying to measure a fast, impulsive signal from an amplified analog microphone using an ADC pin on the nRF54L15-DK. When I read the same signal using a 12-bit...
Our production facility has some concerns about using the OTP parameters. Specifically, they are concerned about writing the wrong value and then needing to scrap the device...
Hi,
We are developing a product based on nRF5340(ncs 3.1.0) and using MCUboot for OTA updates of both app core and net core.
During an OTA update, the following issue...
Hi Team,
I am working with nRF5340 and have a few clarifications regarding SWD protection (APPROTECT / ERASEPROTECT).
While the application is running, is it possible...
We have an unusual issue.
We are using the nrf 17.1 SDK for a custom board with the nrf52840 in tickless idle mode (RTC1) - using the available port_cmsis_systick.c for...
Hi there
I'm using the HCI UART bridge from NCS v3.2.1 in zephyr/samples/bluetooth/hci_uart with the provided overlay-all-bt_ll_sw_split.conf on an nRF54L15Dk and our Bluetooth...
