After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Hi,
I'm working on app based on ATT_MTU Throughput Example from SDK 13.1, but I added Thread support and now working with Thread SDK 0.10.0. I have a problem with advertising...
I have a hard time understanding precisely what an Element is and how it differentiates from a Model when talking Bluetooth Mesh.
The only definition can seem to find of...
Is there any way to detect / prevent the use of range extenders?
When using a central & server with low TX power, the range is say 10m.
Now an attacker can use a relay...
Hi all,
I have been using Nordic chip-sets for a while mainly for BLE applications. I am now developing a simple lighting product based on Nordic nrf51 family chip-set where...
hello!
i am working with the component nrf52840 v0.5.1 and i need development a thermal profile according with the datasheet of the component nrf52840 v0.5.1
could you...
I'm using op-amp(LM358), condenser microphone and PCA 10028.
My project collect output values of op-amp and broadcast that.
But, noise was occurred while it is advertising...
I'm using the ble_app_multilink_central example app.
In the pca10400.h I changed #define BUTTON_PULL to NRF_GPIO_PIN_PULLDOWN.
The problem is that the first pin interrupt...
Hi
I'm creating an android app for smartwatch(used nrf51 ble),I have two questions
1.I used ANCS(Apple notification center service) in my android app,but nrf51 device...
I'm using the SD (nrf52) MBR to update our custom bootloader, in a battery powered device.We have some custom hardware which is used to disable our LDO, to enter a "Ultra...
Hi Everyone,
Recently I have been trying to measure the current consumption from the dev board.
I have set up the board as instructed by cutting SB9 and soldering SB11...
Hi,
I see intermittent incorrect values from the saadc. The code is described here .
The graf shows battery voltage in mV over about 4 days with one sample per minute...
I am getting following errors when compiling source code in Keil-5. Any one suggest me what i am missing to define symbol?
linking...
._build\nrf51422_xxac.axf: Error...
Hi,
We have devloped PCB based on nrf52832 as beacon.
We have also developed firmware for that and it will advertise for some and than go to sleep mode and after some...
Hi,
What is the minimum number of symbols in preamble nRF52840 has to receive in order to receive full packet on Coded PHY? I can see that it can easily receive packet...
