Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi there,
I always have to start up nrfconnect-5.0.2-x86_64.appimage and then select the power profiler. How can I directly start up the power profiler?
I can see that...
Hi there
I wrote a program (include of advertising, pairing and connecting over service, characteristics) for nrf51822QFAA and work well for C0 build code (nrf51822QFAAC0...
I want to know the power saving mode of nRF5340. Dose this chip set have the following mode ? 1. each BT products connencts, however, the data were not send. above condition...
Today I tried to use the bt_conn_le_param_update() method to update the connection parameters, using the following values.
interval_min = 3000
interval_max = 3000
latency...
Hello,
We can successfully build and flash the ncs/application/asset_tracker_v2 example code in nrf9160. But when trying to boot up, it throws the following error:
**...
Hi there,
I'm using a nRF5340 to generate an 8MHz signal and would like to force the HFXO to always be used as the HFINT is not accurate enough. I have verified this with...
Im following Lesson 8 Exercise 2 – DFU over USB.
My project is in its late stage and now I tried to add DFU over USB but Im getting #error "Serial recovery selected without...
Hi there
My costumer was not able to update the cpunet on a nRF5340.
A lot of troubleshooting now led to the insight, that the costumer used only the app_update.bin...
I had a project that was successfully building in Visual Studio code months ago (June 2024) with Toolchain 2.6.1 for the nRF52832. I have just had time to pick it back up...
Hi Support
I am just checking if Nordic supports hosts other than NRF hosts for the nRF7002 WIFI chip.
I am looking for support for the STM32U5 / STM32H5 mcus - for...
We are develping the BT production by using the Nordic sample program (SampleSoft_NRF5340-AUDIO-DK). ( nRF Connect SDK version is SDK25.0. ) Does this software certify to...
I have a existing design using nrf52810 soc I want send and recieve data using uart --->nrf52810 to nrf52810-->to uart data is custom and have approx 120 bytes, should I send...
I know this exact symptoms has been described many other times, and I apologize. However, I carefully searched through all the previously asked questions in merit and could...
when I run this application, it display Error :
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/applications/asset_tracker_v2/README.html
*** Booting nRF Connect...
