Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hello all,
I'm fairly new to BLE and Linux BlueZ.
I'm trying to interface a Mikrobus BLE module based on nrf52840dk to our Yocto based Linux SBC (Rugged board i.MX6-UL...
Hi Nordic Team,
I am new to embedded developing and I am learning about logging data while working on nRF connect sdk" .
kit:nrf5340
SDK: nRF connect SDK v1.5.0...
I'm finding that the MCUBoot stays stuck in bootloader mode sometimes when using a CONFIG_BOOT_SERIAL_DETECT_PORT.
I've narrowed it down to setting up the GPIO as input...
Dear !!
Good day!!
I want to change the device name using command from mobile along wither after setting the device name i want update the Password, so can you share...
So,
I've got a working framework for my project - a battery powered appliance that will occasionally trigger one of two solenoids, timestamping the operation and subsequently...
I've got an issue where calling a function is overwriting a variable in the calling function. See attached screenshots. In the first, byte is 0x1b. After stepping into the...
Hi,
I am trying to send data over UART to a dispensing unit using Space Parity but am unable to do so since NRF51 only supports Even Parity. Is there any work around through...
Hello, I am trying to implement 1-1 connection between a central and a peripheral, with these (classic) requirements : - when starting central, scan for any peripheral with...
Hi,
I am having some trouble getting optimal power consumption while using the SAADC.
I've tried running the example given here 2766.nRF5_SDK17.0.2_ble_app_beacon_lp_saadc...
Hi,
We are trying to investigate the interval noises of our custom developed sensor board with a digital accelerometer (With SPI interface).
After checking the software...
Hello NRF ,
I have used NRF52832 with BLE advertise and peripherals connected on two different I2Cs ( temp sensor and gyro sensor ), One SPI( LCD Display ) , three GPIO...
I'm working with nRF52840 dongle, i installed nRF Connect for Desktop on windows but the led didn't start pulsing red. Has anyone else had an issue like this?
I am using SDK 16.0.0. I want to switch from a NON-CONNECTABLE, NON-SCANNABLE advertisement to a CONNECTABLE, SCANNABLE advertisement. I launch the first advertisement and...
Hello, I have a bit of a weird case. I'm sending data over Bluetooth. In the begging, I wrote whole data handling in the main.c main loop. everything worked nicely, so I have...
