Dear Nordic:
I try to use pca10040 DK and SDK is nRF52_SDK_0.9.2_dbc28c9.
Test nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\UART the function work well on my DK.
I...
Sometimes windows lose the connection to the nRF51 Dongle. The only way I have been able to reconnect to the dongle is by unplugging and replugging it to the USB port. I have...
app : nrf tools on git hub
s130: sdk v11
s110: sdk v8.1.0
example : nrf_ble_uart.
after modify, it happen, is there some definition shoud modify in app?
by the war,the...
Hi......
the board advertising correct,and it work normal (connect,send and receive data),bug it's name can not display in app scan menu. the definition is "liu",but displaying...
HI,
with the new version of the bluetooth website, i can not find the link to overview the profile,service,characteristic and something else related to it.
thank you.
I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
I am attempting to implement AoA using the nRF5340 Preview development kit and 3 BMD-360 modules with the nrf2811 SoC.
In searching the devzone I see multiple comments...
Hi ,
I am following the instructions here:
https://bifravst.gitbook.io/bifravst/bifravst-on-aws/simulator
to deploy the web application, and the web application says...
Based on SDK15.3(nRF52810) app_uart example, stop the adverting, turn off all the peripherals and enter idle_state_handle(), but the static current is still about 10uA. Rememeber...
I set up the environment for the nRF9160 as it was specified and downloaded the git-hub code https://github.com/NordicPlayground/fw-nrfconnect-nrf (environment 1) and I tested...
Hi all,
I am using 2 SPI's in my design. I enabled SPI0_ENABLED and SPI1_ENABLED in my sdk_config.h.
SPI0 works fine. But SPI1 MOSI pin always sends 0xFF.
My pin configuration...
Hi, I m sending a packet in mode Nrf_1Mb to another board nrf5340-PDK.
When I try to enable NRF_REGULATORS_S->VREGRADIO.DCDCEN=REGULATORS_VREGRADIO_DCDCEN_DCDCEN_Enabled;...
Hi,
I am using mesh SDK v3.2.0 and SoftDevice(s140 v6.1.1) to build light switch server firmware. And also insert the uart code from nRF5_SDK_15.3.0_59ac345. So the light...
Hello:
I am studying thread samples in nRF9160.
There are two thread samples: "zephyr\samples\basic\threads" and “zephyr\samples\synchronization”.
But I can't find main...
Hello,
I received information that i could turn the modem on and off not more than 60 times within an hour.
We are however working on a real time system, which may...
Hi everyone,
Currently I am routing hardware for an upcoming project using the nRF5340 and it's time for a sanity check.
The goal is that the HW works well enough w/Engineering...
Hi,
I've been trying to set up a SPI <-> USB interface between an FPGA and my PC via the nrf52840 dk. My ultimate goal is to stream 1Mbps+ worth of data, but right now I...
I have a custom characteristic on which I send ASCII strings as notifications similar to NUS. Is there a way to have the Bluetooth Low Energy app in nrfConnect show the data...
I am writing a BLE application on the nRF52832 using S132 v6.0 and SDK 15.2, and my application is using the nrfx_SPIM driver. I find that once I initialize the spim driver...
I am using the nRF52840, SDK 16.0.
I'm attempting to advertise on the coded phy and the 1M phy simultaneously. This works.
I have two phones, one that supports coded...
Hi,
I tried to enable the CMSIS in my CUSTOM Project but I see the following error and the CMSIS configurator is empty. Please guide what would be the possible problem....
