Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi all,
I am looking for some advice on how to implement a couple of extra characteristics(Related with battery) with the Battery Service apart from the usual Battery Level...
In " nRF51 Series Reference Manual ", in TWI chapter, it is mentioned to configure the GPIO pins with drive strength S0D1, to secure correct signal levels on the pins used...
In my application I'd like to use nRF52810 due different reasons. Since we're still in evaluating phase, without even choose a brand and related EVK, I've some basic questions...
Hi,
I am adding "install codes" function to my products.
Questions are
1. How many entries can i add with "zb_secur_ic_add" at ZC site?
2. Can i retrieve mac/ic (install...
Hi,
We are starting to measure the power of our nrf52840 based design.
I'd like to establish the power number for Idle() , since system will be in Idle() most of the time...
Hi,
I"m using SDK 15.3.0 with an NRF52840 dev board. I'm trying to record the timings from an incoming IR signal. In doing so I'm using LPCOMP with an analog input pin to...
I am trying to use the RF5 BLE CLI (Nordic NUS driver).
I need a plug and play COM port for Windows, iOS, and OS/X. This has to work for a customer.
It pairs easily, but...
My team is in the process of developing a product that uses the Fanstel BC832 module and have been running into issues trying to implement buttlonless DFU in our application...
I'm developing a fingerprint-related project. When the finger touches, the fingerprint sensor generates a pulse signal. NRF52810 will triggers a GPIOTE callback, then wakeup...
I try to bonding func using ble_app_gls example.
just connect is fine.
here is ble_evt handler
for trying connect bonding, I use pm_handler_secure_on_connection(p_ble_evt...
Hello,
I would like to use the nRF52840 for a wearable. It should be powered by a lipo-battery with 3.7V. Therefore I would solder it to the VDDH and Ground Pin (VSS). Is...
Hello .
I try to connect my JLink to my nrf51422QFAA cunstom board. And I use J-Flash to test ifg it can readback and it is OK. But When I try to use nrfjprog, I got some...
We would like to create the boot settings page and merge it with the application and flash the merged hex file using J-Link and nrfjprog.exe in production.
Currently in...
Hi,
We are looking for a secure NFC solution for our application. We want to make sure the tag is secured (cannot duplicate) and the reader, which is a NRF52840, needs to...
I am using SES V4.18 with SDK 15.3.0.
In sdk_config.h, I have set APP_VERSION_MAJOR and APP_VERSION_MINOR etc...
Is it possible to add these numbers to the output file...
