Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi!
I am using the Segger embedded Studio with PCA10056 successfully. Now I have to evaluate LARD DVK-BL654 (because it has external antenna). I found a guide which says...
I am trying to flash my custom board that uses the Raytac nRF52840 via SWD. I am trying to flash a custom bootloader onto the chip; however, JFlash is giving me an error....
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi there, I'm using nrf52840 with OpenThread SDK and I wanna know, what is default radio mode of this device? Because we also have another project with Bluetooth and we observe...
SDK15.0 whitelist hardfault
when setting the sd_ble_gap_device_identities_set using the iOS nrfConnect the non DK board hardfaults.
On an android device all works fine...
Hi,
I'm adding some custom buttons to the NRF52-DK and I've been playing around in PCA10040.h. So far, I have everything working with 4 buttons. The DK can connect to...
Dears,
Now I am using nRF5_SDK_15.3.0_59ac345 for my project on nRF52810.
I found a bootloader example at
\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040e_ble...
hello, I am trying to integrates saadc & bluetooth because in my project adc sample values are comming from sensor & these values is send through bluetooth_uart app. so can...
Hi,
I'm in the process of evaluating the nRF9160 DK and this I want to be able to control the diferent peripherals on the DK so I can reduce as much as I can the current...
Dear supplier
I want to read 10 heart rate sensors that are connected to 10 person's bodies and then display them on TV. How can I do it?
Can I use nRF52832 chip? Can...
Hi
I am using nRF5_SDK_15.2.0_9412b96 on pca 10040
I am storing over 2000 ADC readings and then printing them out once my test is complete. I get "Logs Dropped(x) " messages...
Hello
I am writing a program using SDK 15.0.0.
I'm trying to merge SPI and TWI programs into BLE programs.
I used keil before to confirm that each program was working...
Using Ozone v2.54, if i halt program execution and then resume again, I get a NRF_FAULT_ID_SD_ASSERT fault, with info = 0, pc = 0x142CA.
softdevice: s132 v4.0.2
The error...
