I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hi,
I'm trying to test adding my own custom service, but have errors when I tried to add a 128bit UUID, the test code is simple, in the service_init() function, I just added...
I am using nrf52832 and sdk 14.2.0.The software I am using is keil 5.17.the error is as follows:.\_build\nrf52832_xxaa.axf: Error: L6915E: Library reports error: __use_no_semihosting...
Hi,
In nRF SDK15, Bluetooth peripheral examples for HID devices were limited to keyboard and mouse. By any means, can we configure Nordic device as a game controller?
Hello,
I am currently learning the PWM peripheral of the nRF52DK and am a total beginner in PWM.
I have tried running the attached program and this allows the LED0 to...
Hello,
I am working on a project which requires radio transmitter and receiver to work in sync with the SPI. So the setup is as follows the Transmitter transmits a signal...
Hi,
I am trying to write my own dfu updater for the NRF51 chip and I am stuck trying to make sense of the actual DFU sequence described here infocenter.nordicsemi.com/index...
I am trying to set up mqtt between 2 nrf52s and rpi3 with the examples of sdk 15.0.2. I am very new to nrf52, rpi3 and networking. I have read everything needed as much as...
Let's send a string over UART. RTS signal will go low (active). So far, so good.
The problem is that RTS remains active even after sending is done. And because it is still...
I have two boards. I ran the exact same commands on both boards. The commands flash the same bootloader+app+softdevice+app settings hex file. One board reboots into the application...
Hello,
Setup: Running Ubuntu 18.04 inside Windows Host (using VMWare).
Device: nrf52840DK
Operating System (used for development): RIOT
I would like to communicate...
Hi,
I am running IoT LWM2m example. Everything were going fine since yesterday. when I do hcitool lescan, i see following output:
hcitool lescan LE Scan ... 28:45:8B...
I am using the ble_blinky example (s132) and want to increase the number of characteristics. I get the error code 4. I think the storage capacity is not the reason why I can...
Hi Team Nordic,
I started developing a project using SDK 15 using DK nrf52840 .
I went through several threads and started by creating a test folder inside example directory...
Hello,
I have the proximity example updating the battery service value fine using the provided nrf_drv_saadc.h driver. When converting the saadc driver to NRFX (nrfx_saadc...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
