Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
The comment in dfu_init_prevalidate says the following
// To support application versioning, this check should be updated.
// This template allows for any application...
Hi,
As far as I know the ADC pins can be used as digital inputs. Is it the same with NRF9E5? I could not find anything like pros/cons. Datasheet doesnot say anything about...
Hi,
i have been struggling with UICR Config in nrf52. The code:
NRF_NVMC->CONFIG = (NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos);
while (NRF_NVMC->READY == NVMC_READY_READY_Busy...
Dear nordic.
We are developing nRF51822 with S120 as central.
When advertising from Peripheral, RSSI value is changed it's position.
Measured RSSI range is -60 dBM...
Hi,
I am trying to get the sniffer to work on my new Win10 machine.
I am using the PCA10001 board.
I have tried:
SEGGER: 6.00g and 5.12f
Wireshark: 1.12.x,...
Hi to everybody,
I have configured the nrf52 DK (SDK 11) with FreeRTOS and the UARTE with a DMA buffer of 16 bytes and it works. The problem comes when I don’t want to...
Hi,
I'm working on ble_app_hrs_c application with Nordic beacon.
Using nRF51822 Ver.H0 with S120 and modified to using Internal 32.768KHz RCOSC and UART at 115200bps...
Hi guys,
I'm playing with a beacon kit, nRF51822-BK.
It works out of box, no problem but I have a simple question. One of our customer asked me if is possible to control...
Hello,
I am using nrf51 SDK version 10.0.0 along with the nRF51822, and I believe I have found an issue with a macro that is supposed to check the correctness of a bit...
Hi All,
Another question for those out there much smarter than myself...
We're developing an application using nrf52, sdk11 and softdevice s132 2.0.0 and have been using...
I see it is advised not to just stop a timer, but to also shut it down for certain of the nRF52s. What call is necessary to achieve this since I understand it is deprecated...
I want to read the onboard (dev board) buttons which i believe are P13-P16. I want to know the working code.
uint32_t app_button_is_pushed ( uint8_t button_id,
bool *...
I am trying to estimate the memory usage of the s132 v3.0.0 running on a nRF52832. I am interested on acting only as a peripheral with one link at a time only. From app_ram_base...
Implementing my own protocol stack with low-level programming of the radio, can I broadcast by simply programming all units to receive the same address?
No addresses (such...
Hi,
I am trying to use the sdk version 9 for the NRF51 to take ADC samples and trasmit it over BLE over UART found in the link: github.com/.../nRF51-SDK-9-0-0
I downloaded...
