Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hello,
i have a strange issue with my analog input. Every few seconds (not the same database) my signal is getting pulled low.
But i dont know why. The external signal...
I been having an issue using the ZB_ZCL_REGISTER_DEVICE_CB to know when the ZC writes to an attribute that is of type 0x42 String type. It seems that the callback id changes...
Hello,
Whenever we reset our custom board with the USB cable plugged in and powered, the NRF_POWER->USBREGSTATUS has a value of 1. It will not go to a value of 3 ( OUTPUTRDY...
Hello
I meet a build problem, could any one help me solve this?
Mesh build enviorment: ubuntu + cmake
build command: cmake --build /home/yuguorong/work/nordicMesh/build...
Dear community,
I am using the nRF52840 dongle with the connectivity FW and set the max number of connections to 10 in the connectivity firmware (of course the RAM area...
Hello! I have a few questions and concerns.
1) There are two UARTs on nrf52833. UART0 and UART1. How do I get them to work properly? For UART1, work is available only through...
hi ，
thank for your browse，when i develop my keyborad,there is a problem in the use of usb.
this is my board hw:
and use pca10056 kd,and program the hex of road...
Hello, everyone!
I have arduino nano 33 ble board. I understand that this board contains nrf52840 and can be used in nrf sdk. I will connect the debugger pin and J-link...
Hello!
I am using an saadc examole to get sensor value using AIN3 and sending it on ble but now i want to make it interrupt base example can someone help me out how to do...
I am researching a way to send audio from a Microphone on an APP in iOS or Android and came across the Thingy:52. Is it possible to get some guidance on the App side to transmit...
I would like to use an analog microphone to generate a voice signal, measure it by an ADC, and then transmit the sound to the host. This is the cheapest solution, but I'm...
Hello,
I'm trying DFU from here . It works successfully with nRF52833 DK Board before Appendix 1.
The question is how to combine all which it is bootloader + sd +...
Hello all, I have question about ppi.
Like code shown above, I'm using ppi.
Here, MUX_INPUT_2 and MUX_INPUT_3 are name of pin.
I'm changing their state: from low to...
Hi,
We would like to know the default state of the NRF52840’s GPIO pins - is it high, low or open? The reason for this question – we need to know these pins’ behavior/state...
