Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hi ,
1. I learned from Nordic FAE that on the nrf9160 module, 10 minutes after the edrx mode, the nrf9160 module automatically powers off the sim card to save power,
2...
Hello Team,
I want to use scheduler to schedule two tasks i.e task_1 and task_2. The task_1 and task_2 are as follow:
void task_1() { printf("Task 1 ran"); }
void task_2...
Sorry this might be a stupid question.
We are evaluating some modem to develop a IoT device, NRF9160 comes up to our list as its tiny size.
In the design of IoT device...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
We are using NRF52840 and we have a watchdog timer connected to reset the Nordic, if needed. What is the minimum and maximum time need to insert a reset on Nordic?
thanks...
I want to transfer sensor data to a raspberry pi using the in-built USB on nrf52840. The example codes have the following classes: CDC_ACM, Audio, HID and Mass storage. I...
Hello,
I am just curious wether there are any specific recommendations or requirements for the package-sizes of capacitors/inductors listed in the BOMs of the nRF52840-reference...
Hello,
I am working with the latest version of nRF52 SDK 13.0.0, when I was implementing my own bootloader application, I tried to start an app timer in my code to invert...
Hi there,
Could you please tell me the exact part number of nRF9160 and nRF52840 on Thingy: 91?
I cannot find the specific information even though I looked through the...
Hi All,
How many nodes can connect to a node in ble mesh network. I go through code in ble mesh, but i did't found the answer.
Can any one please tell me.
Regards
...
We have an application using SDK for Thread 4.1. The application requires sending large custom commands over CLI.
We increased the size of NRF_CLI_CMD_BUFF_SIZE in sdk_config...
Hi, I am using the nRF connect app to test the BLE function on my code. I am able to scan the device and Service UUIDs just fine. However, when I click on the "connect" button...
Hello,
I have been trying to implement the tinycrypt ECDSA algorithm for our product. I had sampled the implementation in a sample project with ECDSA being the only implementation...
Hello I am working on an application which is based on the ble_thread_dyn_mtd_coap_cli_pca10056_s140 example. I then used the ble_app_rscs example so that I could add Bluetooth...
