I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi,
I am developing a device based on nrf52840 soc, and the rule of my device is peripheral. I want to know, if a connection was established, could my device start the...
Hello,
we are currently in the development of a low power, battery powered device that needs to count slow pulses (period between ~10ms and several seconds).
At the...
I have a custom nRF52840 board that transmits sensor data (using UART) to a PC with an embedded Bluetooth adapter. I have a code on Matlab that works just fine (using blelist...
Dear Sir.
I am using Master SPI to drive 2 slaves.
Both spi are referenced within Interrupt routine ,
When both spi;s slave are referenced I get an error
err = spi_transceive...
This question has been asked before. I have been using the previous threads to cobble together what is below. I opened a new ticket as reopening (really) old threads is generally...
usb hid how to send 6 bytes of data, app_usbd_hid_kbd_key_control can only send 1 key value, I see that app_usbd_hid_kbd_ctx_t can fill 6 bytes, please see
typedef struct...
Hello,
We're needing a lot more RAM than what nRF91 has, does current nRF Connect SDK support parallel PSRAM on Zephyr somehow or is the development on a roadmap?
Hi there, I want to use CppUTest on the nRF52 to start developing my personal and not so personal projects. I am using the SDK for nRF52, with PCA10040's board. For the moment...
My nRF9160 is plugged into a Raspberry Pi and located somewhere far away from my office, where it can receive an LTE Cat-M signal. I'd like to update the LTE firmware, but...
Hi,
Recently we got Thingy91 and testing the GPS.
we have our custom nrf9160 board and GPS is working and getting coordinates in outdoor.
Im running the sample GPS application...
Hey All,
Due to my findings with this ticket ( https://devzone.nordicsemi.com/f/nordic-q-a/62255/lte-link-monitor-timing-out ), I decided to try and compile the LTE Link...
Hi All,
I am using the light switch example and have modified it a bit to send packets of data. I am able to send data from the client to group address, by setting the...
I have two beacons which are UUID filtered successfully.
I am trying to fetch major but this cannot be done just by putting an offset to p_adv_report->data.p_data. I noticed...
Hi,
nrf52 using from ble-peripheral-> ble_app_uart examle
In that ble_app_uart example receive the data from the android is ok.
But,i want transmit array type of data...
Hi.
setup is 52832, S332, SDK 15.3.0.
issue is about reset voltage.
I use CR2032 for power supply.
repeat fast put on and put off CR2032 on custom board, sometimes...
