hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello,
I successfully downloaded SAADC SDK example in the peripheral folder. The hardware setup is as below ,
The pin configuration for this is as below
...
I tried implementing
https://github.com/andenore/NordicSnippets/blob/master/examples/temp/main.c
But i get 2.6V without connecting any of the Analog pins.
Exactly...
I have attached an Arduino INO file that I wrote early on in a project. It runs a probe. It is an amazingly simple probe but especially important. I am making a simple opacity...
Hi Team,
I planning to use vibration motor with nrf52832.
vibration motor will give maximum buzz on 20.3KHz(50 duty cycle).
So my question is
- Can I achieve 20...
Hello I would like to use the extended advertinsing packets from Blutooth V5 as used in the "ble_app_rscs" example. My problem is that I can't connect via the extended advertinsing...
It looks like NRF_LOG_INFO doesn't copy the data that is sent to it as per the below example. Is there a way around this so that I can reuse long buffers that contain either...
Our purpose is to integrate BLE 5 in our embedded application, and do it quickly.. We basically need to send/receive data with maximum throughput.
Per thread below, we are...
I am having some issues bootloading the dwm1001 board.
I am able to flash over UART and BLE using nrfutil and nrfConnect with:
s132_nrf52_6.0.0 softdevice
pca_10040...
Im trying load a TWI sensor custom built with LIS3DH, and it is showing following error.
The xml file looks as below
Can you kindly guide me, how to resolve...
Hello. I'm trying to create a new project or open existing examples with eclipse.
I tried to import "Existing code as Makefile project" and File->New->Makefile Project with...
I would like clarification on the use of the nrfConnect programmer for RE-programming the "dongle" a.k.a PCA10059. NOTE: NOT "programming a virgin dongle" Reference: The user...
I'm having trouble with certification in China. Here is what they are getting for spectrum using the nrf52832 with the nrf_radio_test_example. The lab is saying that this...
Hi,
We need send packets continously, and need adjust TIFS slightly when real packet interval is shorter or longer than expected.
The radio shorts register is set to RADIO_SHORTS_READY_START_Msk...
I tried implementing the custom BLE example in the below link Im facing two problem 1. ble_cus.h header file throws error
Main
ble_cus.h
ble_cus.c
The error...
I have just integrated the Buttonless DFU example code into my project and I am able to successfully update my device using nRFConnect. I'm using the NRF52840, S140, and SDK...
