Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi,
I have some issues flashing or debugging my Thingy91. The problem seems to be related to my specific Thingy91, as I have another Thingy91, which I'm able to flash...
So, I am updating our advertisement data on a regular rate using a timer from freeRTOS on custom piece of software the is for the nRF52840. When only the app code is loaded...
Hi,
I'm trying to deal with long write events (37 bytes long) but on adding a second long write characteristic I'm facing the NRF_ERROR_NO_MEM error on adding it.
The...
Hi Sir,
Since Zigbee_Thread 3.2 released, we prepared two 52840-DKs for consumption test.
One is the door lock example (device #1 Thread_Zigbee_3.2.0\examples\multiprotocol...
I notice that the question has been asked as far back as 3 years without any answer!
There are several parts of the datasheet that mentions internal reference voltage sources...
Good morning Mrs
I have a bluetooth module SKB501 which integrate a NRF52840 chip. In that NRF52840, i want to test a code (ble_app_uart) include in the "nRF5_SDK_15.3.0_59ac345...
Hi. We are using RTC2 in our application to trigger an event at 256Hz. We also have a compare running to trigger a compare event at 32Hz.
I have found that over an hour...
Hello guys,
I am using nRF52840 and SDK 15.3.0. Trying to use SPIM3 device because of the speed.
In my sdk_config.h file, I set both NRFX_SPIM_ENABLED and NRFX_SPIM3_ENABLED...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I want "nRESET" to be set without pull-up. How can I use "nRESET" without pull-up?
Hello,
While importing the needed libraries for a project I stumbled upon an error in the app_error_handler_gcc.c and app_error_handler_iar.c files. The error is
nrflibraries...
I am using a SPI peripheral on the nRF52832. If the SPI bus is busy when I call
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST);
the routine returns...
Hi, I'm working on a simple SAADC acquire in scan mode.
I create the two following function:
I was able to init and read the adc without problem.
If I remove the...
Hi All, I'm doing some investigative around existing mesh models. In the Mesh Model Bluetooth Specification, Section 7.1, we have a specification, for example:
Generic OnOff...
Hi,
I am considering now the timings during a BLE connection, especially for long range. For that I came across the range delay given in the latest BT Link Layer Specification...
Dear nordic,
I have application that developed using development kit pca10040 . I want to change it to supporting nRF52810. i follow the instruction the link :-
http:...
