I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
on the nrf52832 I am configuring pin 10 as an input. There is either 0 or 3.1V on the pin depending on whether a charger is connected to the board.
When I read the state...
Just stumbled upon this:
#define TIMER_PRESCALER_PRESCALER_Msk (0xFUL << TIMER_PRESCALER_PRESCALER_Pos) /*!< Bit mask of PRESCALER field. */
Should be
#define TIMER_PRESCALER_PRESCALER_Msk...
I am working on project where I am storing and reading data from an SD card. During the initialization, I would like to print the full contents of the root directory - "/...
Hello,
I have a problem through which unfortunately I'm not able to come across alone. I'm using nRF52832 with softdevice and UART central example from SDK14.2 (..\examples...
I'm using nRF52840-PDK. I created a custom ble service following this tutorial ( github.com/.../custom_ble_service_example) and sent my sensor data over bluetooth. Now I'm...
Hi ,
I am trying to disconnect a connected central (phone) by calling sd_ble_gap_disconnect from my nrf52 configured in multiperipheral mode. . The disconnect call returns...
I am trying to time a capacitor discharge through different resistance sensors for greater resolution than an ADC. I did this using the GPIO functions initially but the SD...
Hi,
Is it possible to use Segger Embedded Studio with nRF51?
I see on your web site it's supported with SDK 14 or greater but this SDK is only for nRF52.
My product...
I have problems with my custom board.
I developed the firmware with the nrf52840-PDK and there the firmware runs standalone (with RTT connected and without) or when debugged...
Hello
I am working on nrf52382,sdk11,softdevice 2.0.
/cfs-file/__key/support-attachments/beef5d1b77644c448dabff31668f3a47-fd3fce63fa6d4ddfa73158194e4d87c3/battery_5F00_pins...
Hello,
I am writting a batch script to flash a PCA10056.I use it to flash the softdevice, the bootloader and my application.
The script works well and flash the device...
Here NRF52 TX pin is connected to Battery to measure voltage Level. i am using NRF52 with SDK 11 and s132 soft device.
Here is my Schematics
here BATTERY is connected...
Hi
I am working with the twi_scanner_pca10056 example found in the SDK. Using a oscilloscope I can detect the logging messages on pin P0.01, even though sdt_config.h defines...
