I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hi all,
Is it possible to check whether there is an active carrier with the nRF24L01+? I've got the TX and RX chips configured via SPI correctly (I think), yet I can't...
What do I need to take care of when I solder CE pin to VCC? (to save I/O)
NRF is mostly in RXing state, and sometimes TXes.
So far I figured out to go from RX->TX mode...
Hi,
Can I use RTT to build a communicate to a command line interface (CLI) in the device?
This would require that the program does not block, as it does in SEGGER_RTT_WaitKey...
I'm using the UART application in nRF Toolbox Version 2.4, iOS 8.4 on an iPhone 5S.
Is it possible to save the logged data to a file, or in any other way get the data out...
Hello,
I am using an Eclipse GCC environment with the following setup:
Ubuntu -> 14.04 (Trusty Tahr)
Eclipse IDE for C/C++ Developers -> Version: Luna Service...
kit: RF51DK.
sdk:nRF51_SDK_8.1.0
SoftDevice:s110_nrf51_8.0.0_softdevice.hex
I want to use 5 channels pwm to control 2 servos and 1 motor;each servo uses 2 channels pwm...
I included the DFU service in my project. With the MCP on my computer it is working fine.
But when I try to perform the DFU over the MCP(v.3.4.1) app on my android device...
I'm migrating firmware from SDK 6.x to 9.0.0
I found pretty many changes in SDK APIs.
Do I have need or do you recommend to upgrade to new SDK ( for bugs / problems...
Hi!
I'm working with nrf51dk with s110 Soft Device.
I need to read ADC every 2ms. In order to achieve that, i made timer with interrupt after 2ms. here is my code of initialising...
I have a quick question about the use of the nRF51 DK's Debug Out port (P19) to program external nRF51 boards.
The user guide says that the DK will "detect the supply voltage...
I have some questions about 2.4G protocol stack gazell&ANT+&BLE .
gzll&ble :
choose nrf51822 ，and use S130 SOFTDEVICE,then we can achieve gzll&ble coexitance. is that...
i wonder nRF51822 (256K flash/ 16K ram) Support IoT SDK / IoT SoftDevice.
i test nRF51822, IoT SoftDevice , CoAP Server Example, but not Work.
i confirm nRF51-DK (nRF51422...
Hi, Nordic staff.
When we develop , manufacture and sell products using the gazelle , do you have any restrictions ?, I mean, do we need a certification or to apply for...
