Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hello Sir,
I am working on direction finding. I use the nRF52840 DK to flash the code onto an nRF52811 (custom board) that supports direction finding. In the build configuration...
I was trying to receive some data using "i2c_transfer" then continue the receiving without starting a new transaction.
Stop bit was sent if I configured to use it or not...
My project has a nrf5340+external flash, and an external USB-C connector. The device exposes a USB file system (FAT) which is hosted on the external flash partition, and appears...
Hi Nordic
Q1.
HW: nrf9160 customer board. One USB-to-RS232 cable is used for PC sending AT commands (UART2).
Another USB-to-RS232 cable is used for PC collecting modem...
I am currently evaluating the Nrf54l15 viability for a migration from the Nrf52 for our products. I've been able to advertise, scan and connect with success but I can't find...
Hi,
I'm trying to build the nrf5340_audio/broadcast_source application. I'm getting the following error: nrf5340_audio/src/audio/le_audio_rx.c:20:22: error: 'CONFIG_BT_ISO_RX_MTU...
Hi, I have recently created a board definition for our nRF5340-based hardware using the "Create a new board" feature from the nRF Connect for VS Code plugin. I'm using SDK...
Hello,Nordic team
I am programming with nrf52833 and ncs v2.9.0
I am going to do dfu not by YOUR example(FOTA or UART……)
I flash_write() data to image-1 address，and...
Hello,
Very new to Zigbee. Trying to use nrf 5340 dk as a Zigbee Coordinator to connect to a Thirdreality and a Sonoff PIR motion sensor. No modification (expect adding...
I am using the solution for this exercise to have MCUBoot use the nrf5340dk's external flash for the secondary partition in my own project. I have done the following:
1...
Hi,
I have a question about official suported Bluetooth version on NRF5340, becase there's some conflicting informations.... On this link, it's written " Bluetooth 5.4...
I have nrf52840DK less than 6 month. It has been sitting in my drawer and has some sample code in it which is detecting button press and light up corresponding leds.
Last...
Dear Nordic Team,
We just started the development with NRF54L15 EVK and fabricated and Assembled PCBs as well using NRF54 MCU.
In our product we require 4 timers peripherals...
Hi,
We are currently using the NRF52832 in one of our products. Due to software requirements we need more RAM. Therefore the product is going to be redesigned for the NRF52840...
