hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi,
It is understood that,If to the function on_cts_c_evt BLE_CTS_C_EVT_CURRENT_TIME event is passed as arguement then it gives a call to the function current_time_print...
Hi all, I'm using a custom board and I ask you if it is possible to use nrf_log (rx \ tx) on port p1.10 p1.03 or if I can use nrf_log redirecting to usb. I read somewhere...
Hello, the directions indicate that it is possible to use Windows Subsystem for Linux, and you instruct us to use version 2 of WSL, but I have no access to the COM ports so...
Hi,
I want to know how logging is happening in the nrf 17.0 sdk and nrf5.0 mesh sdk is it different in any case in nrf sdk and nrf mesh sdk? As, in infocenter of nordic...
I just received my nRF52840 dongles and am trying to get nRF Connect going (macOS El Capitan).
Installed the J-Link package per instructions, and the nRF Connect 2.6.0 app...
Hello, I'm trying to port my code (working in production) from 52811 to 52832. I have several crashes on a piece of code at the start of my application that check the NRF_UICR...
I modified the asset tracker application as follows (to reduce power consumption):
1) Added lte_lc_psm_req(true); at the end of main-function. In prj_thingy91_nrf9160ns...
Hi!
We've got a product where we need to update the bootloader from within our main application. However while we can happily erase and write flash before 0xf7000 (obviously...
Hi Team, I am using nRF52832 to develop a device that sends Bluetooth signals to a smartphone. I am sending only small, 1-byte pieces of data, but it is critic to send them...
The NCS documentation refers to the Partition Manager from a few places to describe how to layout areas for MCUboot, etc. However, I don't see any documentation there for...
Hi,
Is it possible to use write without response when sending data from NUS Central app?
I'm using NCS SDK v1.50
I replaced in nus_client.c:
err = bt_gatt_write...
I am using nRF52832 on my custom board. The SoftDevice, secure bootloader and my custom BLE application are flashed on my flash.
After processing a single GPIOTE event,...
Hello, I am using nRF52832 to develop a device that sends Bluetooth signals to a smartphone. I am sending small pieces of data but it is critic to send them as quickly as...
Hello,
I have two boards. A nRF52840DK as central and a BMD-300-EVAL (contains a nRF52832 chip) as peripheral. I flashed ble_app_uart_c on the central and ble_app_uart on...
Hi.
I'm using nrf52 dk and planning to make PCB Custom.
I want to ask three questions about nrf52 dk.
1)
First, I downloaded nrf52 reference circuirty(Schematic...
