I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I have taken the examples\peripheral\serial example and made minor changes (NRF_UART_HWFC_ENABLED to NRF_UART_HWFC_DISABLED, commented out bsp_board_init).
I have a USB...
Hi
Our requirement is to do Over-the-air DFU at the bootloader level for nRF52840 devices on thread network. Can you suggest if this possible at the bootloader level? If...
I got a J-Link mini Edu today, and I wanted to try to experiment using it with my NRF52840 dongle.
To test it out I tried uploading some of my code and some examples, but...
Hello,
For a project, I'm trying to create a connection between an android phone and an nRF52832 via bluetooth after scanning nfc. But Everytime I tried it, a dialog appears...
I would like to program a nrf52840-Dongle with OpenThread's ot-ncp-ftd.hex image over USB DFU. After putting the device into bootloader by pressing the physical reset button...
We have two evaluation boards of nrf 52832 Bluetooth modules. we try to connect the modules in one to many network format for that application we flashed the following software...
Hi!
I have a Nordic NRF52840 development kit and am trying to interface with the MX25R6435F flash chip. It communicates over QSPI, so I know I have to go through the QSPI...
Others have had similar problems with pointers for structures. So, I've tried several different methods including one that was suggested in another help ticket. I am writing...
I checked the operation of the application "ble_app_hrs" and I see that the FDS makes a new record in flash memory with every new connection. What is the need and can it be...
Hello I want to use MTU = 247 bytes. For 1M PHY, everything is working fine. When I set the coded PHY, there is a problem. I get the GATT event NRF_BLE_GATT_EVT_ATT_MTU_UPDATED...
I want to tested RF performance ，so i hope send cat-M 6RB@0 signal. For example, the circled part of the picture: ,it's send 6RB@22 signal。please tell me AT command.
Re: nRF52833DK, s113 and nRF5_SDK v16.0.0
It appears that nrf_sdh_freertos.c needs to be modified to support JUST_WORKS and LESC because the softdevice_task() in nrf_sdh_freertos...
Hi
I am working this tutorial . At the end of this, I copied and executed the contents of advertising_init() function but it became NRF_BREAKPOINT_COND.
When debugging...
I am trying to use the GPS from the Thingy:91. Due to the unavailability of Power Saving Mode (PSM) in roaming with my local provider, I am considering what options are available...
I am trying to see/set preprocessor options and they are not visible. I have seen the tutorial which says
project options >> code >> preprocessor should be the way to do...
