Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
I've tried ble_app_uart, nrf_serial.c etc. and none seems satisfactory.
I can write to the logger logger/uart during DEBUG, but it doesn't seem to succeed in RUN.
Question...
Hello,
I'm using :
- SDK 11 s132
- nRF52832
I want to protect my flash against dumping from swd but I'm working also with DFU from our custom app.
Is it possible...
Randomly on my nrf52832, sd_power_system_off() is returning NRF_ERROR_NOT_SUPPORTED and I'm looking for tips on how to figure out why. I'm using a Bluetooth soft device and...
Hello,
May I please check if the following is correct? On the nRF52840-PDK board (v0.9.3, 2017.47), the "VTref" pin of the "Debug In" header is connected to VDD. Should...
I need to upgrade and existing nrf51 S110 system based on SDK 8.x to something that supports the same functionality and also supports both a nrf51 (during the transition)...
I am working on a project where we are using a nordic bluetooth chip and connecting it to a RS485 Bus using UART with Baudrate 115200. The messages sent from the Bluetooth...
I want to experiment with BLE Mesh. I have several BLE400's with nrf51822's. I want to use these as mesh nodes. I want to get the nrf52-dk to use as an interface node. Can...
I recently downloaded Segger's Embedded Studio to compare its performance and ease of use with IAR Embedded Workbench. We have a kickstarter version of IAR for ARM which has...
hi,
i am using nrf5 sdk 14.2.0 ble_app_uart example with keil v5 IDE and i am doing coexistence with nrf5 sdk for mesh v 1.0.1 for nrf52832 mcu.
a have done all steps...
I use nRF52840-Preview-DK PCA10056 v0.9.3, SDK 14.1.0.
I would like update bootloader, but i have any problems.
I do these steps
1.eraseall 2.program softdevice 3.load...
May be I just did not fined a good reference manual for the software, but it really frustrating me to try and understand from examples.
Is there some guide which take a...
When P0.18 is configured as the RESETn pin, is there a pull-up enabled?
In our design we have an external CPU driving the nRF52 RESETn line.
We have a pull-down on that...
Hi all,
I was wondering if the information in the documentation is the right, I was looking for the Memory map for the nRF52 when using the SDK13 s132 v4.0.2, but on the...
Hello,
Could you please indicate where TXPOWER is defined in the "ble_app_beacon_pca10040_s132" code example ? If not defined, could you please indicate what is the best...
