I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I am using nRF52840 Dev kit (PCA10056) , with nRF Mesh SDK 4.0 and nRF SDK 16.0 .
I have such FOUR kits . I have been able to modify vendor model for a sensor to transfer...
Hello everyone.
I'm a fresher of programming nRF52833. I'm doing an application for my final project in my university. What I need is get the RSSI in order to analyse the...
Hello -
I am evaluating nRF52840 to replace the Bluegiga BLED112 in an older product. I am surprised to get very low range from the nRF52850 USB dongle, barely 10-15 feet...
Hi, NordicTeam
Nrf52805 as slave and mobile phone as master to connect slave. NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 247, MTU = 23, the master sends the Prepare Write Request to...
Hi,
I'm developping a new application where the device normally is in low power (waiting button with an interrupt)
while(!gIsButtonSwitched) { __WFE(); }
the consumption...
Hi everyone. I have an application using BLE and OpenThread dynamicaly. I am working with nRF52840 chip with nRF5 SDK for Thread and Zigbee v4.1.0 (Release Date: Week 18,...
Hello, I am using the Zigbee CLI Agent as coordinator, and when a router device or end device joins the network I want to configure attribute reporting.
I am able to configure...
We are running a trial in an open field, where we connect NRF52840 ( GW ) to an NRF 52833 (Node ).
Distance between the units is around 80 meter , we are using Coded Phy...
Hi Nordic team
I tried AWS FOTA and Nordic FOTA at nrf connect for cloud. It did work well.
We now want to set up our own cloud. It's neither AWS cloud nor nrf connect...
Hi,
Sorry for the newbie question but how am I going to use the SAADC to measure 4-20mA current loops? I've used the SAADC to measure temperature, voltage, and resistance...
Hello !!
We are using nRF52833 MCU in our one of project. It is very cost sensitive project. We are proving supply to MCU from coin cell CR2032 battery. Also we enabled...
Hi,
I'm currently developing custom board with nRF52832 and I'm experiencing weird issues.
It's mostly related to BLE, especially on Samsung A series devices (A3, A7,...
I am using custom board nRF52820. I'd done OTA up-gradation with USB connected. Firmware successfully updated on device over BLE and device got soft reset.
After removal...
I am using nRF9160 DK(PCA10090 0.9.0 2019.19) with Indian carrier LTE-M SIM and carried below steps to establish LTE-M communication with nRF Cloud: 1. Upgraded to latest...
