Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Dear
I modify the example of PCA10056 mesh light-server for PCA10059 and it works after I program PCA10059 by nRF Connect –programmer go through USB interface. But there...
Hello,
What is the PPM of LFRC?
In our case, the device will remain in low power mode (System ON, wake up from RTC). The device will wake up at every one hour. Which...
Hello Nordic,
nRF52840, SDK16.0, Softdevice 7.0.1.
I'm using LFCLK to generate an accurate tick for device time keeping (with Prescaler=255, Freq=128Hz, Tick=7.8125ms...
Hi all,
I have a problem when I connect the nRF51822 to my phone.
I use the softdevice S130 and the following code attach .
When I use the nRFconnect in my phone, I...
I have a module BL651 and I want to use it in my dev board. I've found in some previous posts that I have to use nrf52 DK to program externally the nrf52810 in my module....
Hi everyone,
I am using nRF52840 to prototype and I want on certain occations to disconnect the peripheral from the central. On of these occations is when I charge my device...
Hi,
I have a mesh network established with one of the nodes being the provisioner. I am currently using Laird BL652. I want to make an android application for the mesh such...
hi support team,
i have one question about 9160 TCP communication, is data re-transmission fulfillment by the modem? how does it work when in psm mode?
for example, when...
Hello All,
I am working on nRF51822 custom board.Use SDK nRF5 12.3.0 in IAR workbench.
I am use ble peripheral example path given below,
...\...\examples\ble_peripheral...
Hi!
I am trying to add service data to my scan response service data for a custom service. I am unsure of how to set the UUID correctly for this.
UUID declaration:
...
After compiling, loading and running the example code for "ble_app_hts", on an nRF52 DK board, I connected to it using the nRF BLE Toolbox app "HTM" on an Android phone. The...
Hi,
I am working on nrf52sdk devkit. I am using max30208 temp. sensor. I configured one project twi_sensor and it's working properly. but when I merged this code into ble_app_hts...
Hi All：
Good Morning.
I have some problems about how to modify nRF52840 pins in Thread NCP/RCP SPI project，I have checked this link https://devzone.nordicsemi.com...
Hi, l’m have a new question: Is BLE_GATTS_VAR_ATTR_LEN_MAX limited 512?I need to adjust it in my project. I tried to modify the parameter of BLE_GATTS_VAR_ATTR_LEN_MAX , Increased...
