I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi Team,
nRF52840 boards are getting fail continuously not able detect by Host computer.And the boards are no more useful and all boards are brand new only One day we have...
Hi,
I am trying to enable Bootstrap support.
Therefore I set "CONFIG_LWM2M_RD_CLIENT_SUPPORT_BOOTSTRAP=y" in prj.conf.
I also set "CONFIG_APP_LWM2M_SERVER" and the port...
I have built boot-loader hex file from SDK 12.1.0 secure DFU project, without any changes except for public_key.c file.
I am referring to steps mentioned under
Combine...
Dear all,
Hi, I'm Eric.
I m studying spi communication used nRF52832 base on SDK 14.2/example/spi.
That examsignal is below picture 1.
But I want to delay between...
Hi--
I noticed something rather peculiar on the built hex from segger that is programmed onto my nrf52832 chip (firmware image).
The hex looked as expected, until i got...
My ble_peripheral is bonded to ble_central, How do I upgrade at this time ? If you still use the mobile phone APP to upgrade, you need to erase the binding information, and...
Hello,
I encountered a problem when installing nRF_connect on a new computer. As shown in the picture, the attribute "middleware" of null could not be read. Opening all...
I am using as template the MQTT sample app from NRF Connect 1.3.0, for which I want to create my own application modules, I have added the .c files to src, but I am having...
Hello,
We are using the Serial port library with two UARTEs. It defines two instances of the serial port interface: one for receiving data, and one for sending data. After...
Subject pretty much explains the problem. One can just get power from a USB interface, but if I plug our nRF52840 into such an interface, it does not appear to boot into its...
I am trying to use serialization to connect an STM32F4 to an ISP1705. My goal is too connect to other BLE devices and read some measurements. I have tried a few of the examples...
I'm using an example project of the secure serial bootloader (pca10056_uart_debug) and changed some configuration for my custom board. I added RTT debugging and changed uart...
Hi,
One of our projects will use either a LFXO or the LFRC depending on the accuracy.
The product will be exposed to temperature differences ranging from approx. 0 ...
Hello!
I handle mpu6050 sensor in SDK v14. Output of sensor values was successful. And I'm going to use this value to get the angle of the sensor.
The code below is to...
I am using NRF Connect 3.5.0 to program PCA10059 but receive the following error on some dongles when using JLINK programmer
Error while probing devices: Error occured when...
