I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I have ~600 bytes of configuration data total that needs to be saved each after a sensor joins the Zigbee network, details like:
IEEE addr
end point
Join state details...
I plan to use nRF52832 BLE chip of your company. Now I have the following questions: If I use internal 64M RC, can I use Bluetooth function?Is the 2.4g transceiver accurate...
Hi,
I am have programmed my Thingy 91 device with lte_ble_gateway program to collect data from 5 Bluetooth devices and send them to the cloud. This program runs fine, however...
Hi Nordic
We want to study the network id and node id fields in proxy beacon of BLE mesh protocol.
For mesh4.1 sdk light_server example, does it broadcast network id after...
I tried to make CSMA/CA perform on nrf52832 but the SDK example didn't have Energy detection (ED) and CCA sample
How to configuration Energy detection (ED) and CCA ?
If...
Hello,
I am using nRF52840, SDK16 & SoftDevice140.
I am integrating pm_init()(Peer Manager) into my project and I am getting error 0xFFFFB180 from mbedtls_ecp_gen_keypair...
Hello,
We are using the nRF52 DK board and Keil uvision 5.
Using SDK 17.0.0 we can successfully load and build the `examples`. If we choose `examples/peripherals` we can...
Hello, everyone.
I would like to use LSM9DS1, a 9-axis IMU sensor. To test this, an IMU sensor module 'SparkFun 9DoF IMU Breakout - LSM9DS1' was purchased.
This module...
I am working with Zephyr version 2.4 on nRF52840-Dongle for adding ability to scan CODED PHY devices. My host is Raspberry Pi3 with kernel version 5.4.51 v7+, HCI_USB sample...
Hello,
I am trying to run USBD_MSC example using PCA10056 board from SDK15.
It works fine, when creating new file on each button press.
I modified code to create and...
Hello everyone ,
I have question about the difference between periodic message publishing via the module's configuration and publish message by a standard timer.
I notice...
nRF52833 DK i have seen from Images of board that an external antenna will be required(there is a Antenna connector on board). I am wondering if it has built-in antenna or...
Hello,
I am on nrf-sdk v1.3.0 and mwf v1.2.0.
We are updating our product to the above mentioned nrf-sfk version and have noticed that MQTT connection gets stuck after...
Hi,
I enabled flash log backend with NRF_LOG_BACKEND_FLASH_ENABLED set to 1, and NRF_LOG_BACKEND_FLASH_START_PAGE to custom address to keep it as the starting address for...
Hi,
We have successfully created a PCB layout with a PCB antenna following the reference schematic provided by the nrf8001 datasheet. We tested and it is working fine. However...
