Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
Hi,
I'm trying to run the https_client sample on an nrf9160dk, and it's giving me the following output:
*** Booting Zephyr OS build v2.3.0-rc1-ncs1-1440-g"020" !$#a 1...
Hello,
I have purchased this device to use as a BLE sniffer. I have followed this manual to configure the device as a sniffer:
https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3...
Hello.
I'm using a nrf52 dk (nrf52832) + GCC 9.2.1 (9 2019 q4 major) + WIN10 + CLION and I'm trying to build an example project using GCC.
I get the following error: ...
Hello everyone ,
I have question about saving the configuration of Friendship so-that after rebooting the SOC, the friendship's configuration restored without applying the...
Hi, I'm HongJae.
I'm developing a Bluetooth peripheral program with nrf52.
Briefly,
if I send a hexadecimal message(e.g 0x35), GPIO's are ON.
After 1 minute from...
hi,
I found a interesting thing：I use the output function to configure the P0.14（nrf_gpio_cfg_output(14)）. After configuration, the normal output should be low, but it outputs...
hello all,
i am using nRF52832 SoC in my project and my requirement is to write some configuration into internal flash when i flash the program using segger j link.
for...
Hello.
I am evaluating with nRF52833 DK board. I checked both peripheral/uart and ble_peripheral/ble_app_hrs.
Examples work each well on nRF52833 DK. I want to add the...
Hi support Team,
Following are my Questions.
1. Please recommend me three development boards from Nordic. I would like to build the mesh Network.For example one will transmit...
I am seeing a number of issues, but since they appear to be different, I will use different threads.
Setup: have gone to ble_blinky example to keep things as simple as possible...
Hi, i am new to the nRF52840, i like the features it has and i want to create a board using it. In the datasheet it is said to have 2 ARM processors and i want to use it as...
About 3.7V Li-Po battery on spec., can we read adc value from the battery using p0.04(A1) without external voltage divider circuits? In fact, 3.7V battery outputs 4V ,seeing...
Hi,
I'm now planning to test BLE AoA using nRF52833 DK. For now the DK doesn't have antenna array, so I plan to use an addon board like below:
Is there any link or example...
