pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I am running the light_switch example and it works fine works fine , I am using the nrf_application to configure the nodes.
I am using latest mesh sdk and 15.3 nrf sdk....
Hi guys
I had to integrate a CLI module into a project I'm working on, that is running FreeRTOS
after quite a lot of work, I managed to get this working, but seeing...
HI,
I am using nrf52832 dk. I have a sensor that gives a negative voltage. I want to measure the value using saadc.
and can I use differential mode saadc for negative...
Hello All,
I am working on the N51822 custom board.
Using segger IDE, SDK 12.3
Previously i have worked on the sdk 14.3 on the n52810 board. It is working properly...
Hello
I am using pin 1.15 of nrf52840 dongle with transistor with enable pin of another chip. The other chip is a wifi chip which I only want to switch on whenever I have...
Hi All
I am using nRF9160 DK version 0.8.5, and I have gone through this link, downloaded and Installed all the steps, given there. All seems to be running good.
But some...
Hi I am using the custom_bluetooth_service tutorial from https://github.com/bjornspockeli/custom_ble_service_example with SDK v15 and nrf52840 DK.
I am now trying to use...
Win10 + Segger embedded studio
I can get the pca10059 blinky example to work. ( C:\nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky )
I use the NRF connect Programmer...
We are trying to receive high speed data using UART. Currently our source is set to transmit an 8 byte packet once every second.
I have initialised the serial port in IRQ...
Is there a public bug-tracker available (even better: publicly hosted repository)? I'm currently trying to wrap the SDK in way suitable for our internal processes (CMake,...
Hi,
i'm using "cycling speed and cadence" on DK to make a test run. However, my bicycle-watch(base on ANT) doesn't receive any "ANT signal".
Searching in the devzone,...
On the picture channel 2 connected to reset button on PDK.
UART channel drops to GND 4ms after button pressed.
How to prevent this?
Tried this: https://devzone.nordicsemi...
Hello,
at 3.3V the current consumption of my development kit is about 21.5 µA.
Due to the law of energy conservation, I would expect the current at 1.8V to be a little...
Hi,
i'm not getting any signal with a fresh DK and the latest modem driver.
entering AT+COPS=? will make it unresponsive forever. (nordic LTE Link monitor times...
