Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hi,
I want to read and write MAX30100's registers. How can i do that? I tried a lot of solutions but I didn't solve that.
For example; MAX30100's address is 0x57. And...
Greetings!
I am using the SDK Mesh 3.1.0 and Softdevice 6.1.0 with the nRF52840 Dev kit: (PCA10056)
So, in my previous post ( https://devzone.nordicsemi.com/f/nordic...
I am using the nRF 15.2 SDK for Thread and Zigbee. I am currently trying to use the debugger in SES, but when I upload the code, SES complains that it can't find the source...
Hi
my devices use USB HID to PC now, and I have PC GUI.
I want use BLE send My device data to PC ( windows 10 )
if I use BLE HID services to PC
I need to do any...
Hi;
I am trying to add uart central to multilink central examble. I added some of uart part to multilink. i am trying to link two peripheral to central. when two peripheral...
Hello Nordic, for my project work i am using nrf52840 dk. with segger embeded studio i drag and drop the s140 softdevice hex file into the J-Link (chip PCA10056). and i tried...
Hello,
we are using the Nordic nRF52832, and I was hoping to update to the new SoftDevice S113 v7.0.0 as it seems like a better fit for our use cases than S132.
However...
My flash_placement.xml file is here and I am getting this error `.bootloaderSettings' will not fit in region `UNPLACED_SECTIONS'.`UNPLACED_SECTIONS' overflowed by 1024 bytes...
Hi
I have done multilink with uart and getting data from multiple ble_uart peripheral. now i have to read data from only one peripheral . what will do for that.
I am using...
Hello
I was wondering if there have been any changes in supporting IAR for nRF Mesh?
In your answer from about a year ago you wrote that you were not currently planning...
Hi,
I have some questions:
1. How does the process of getting addresses to the Nodes happen in Mesh stack? Is it automatically or I need to set it when I flashed the...
Trying to run the "Alert Notification Application" example in nRF SDK v15.3.0 on either a Windows 10 system or a Ubuntu 18.04 LTS system. Following the instructions, I can...
hi,
i want to use mesh network in my project.our requirement is multiple nodes will be sending data to one master node.is there any example code.
Regards,
jagadee...
Hi,
We have a gateway device that contains the nRF51822 MDBT40 Raytac module.
We are designing a new nRF52832 based sensor and we want to connect 20 of them to the Gateway...
I use nrf_drv_saadc_init(NULL, NULL) to sample AD per second(Blocking type).
But every time the firmware runs, the ADC value always takes several times to stabilize.
...
