pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Working on a migrating RF test firmware that was working on 52832 using SPI to AT86RF233(for 802.15.4). Was able to exercise PHY with that setup to send specific packet with...
Hello, Nordic!
I am wondering about PCB reference design for AoA multi antenna locator based on 52811.
Could you provide it before releasing software supporting this functionality...
Hi. I looked through all the examples in the 15.20 and 15.30 SDK and could not find even one project for SES with it's new linker as an example. all the examples use the old...
To be able to SMS we need the SMSC number stored in the SIM card.
I did not find an AT command to read this, so I gues we need to use the +CSIM or +CRSM?
Regards,
F...
I am using nrf52832 for button less DFU. DFU is working fine when CONFIG_NFCT_PINS_AS_GPIOS is not added in applicaton. When added seems like code is getting reset at bootloader...
I have problems compiling code with modem info support on. My basic problem, I want to establish which modem FW version I am running on.
I added
MODEM_INFO_CONFIG=y
...
We successfully built the mesh bootloader, but want to get RTT working with the bootloader logs inside SEGGER.
We were following this two posts post1 post2 to achieve our...
Hello guys.
I just donwload new version of SDK 1.0.0 for NRF9160 and try run mqtt_simple demo. I didnt change nothing there and there is problem.
I have the follow log...
Hello,
Currently my beaconing application draws approximately 10uA @ 1000ms advertising interval. I am having trouble getting the chip into system power off mode so the...
Hi,
We would like to upgrade an existing product (Bluetooth SIG registered) on the market to the newest release of SoftDevice. Do we need to re-register at Bluetooth SIG...
Hi,
I'm working on a bootloader based on the "secure_bootloader/pca10056_ble" example. Everything works fine until I send the new application binaries (.zip file) and the...
Hello All,
I am working on the NRF51822 custom board.
I am Using the SDK 12.3 with s130 (PCA10028)
1.) Is it right sdk for nrf51822..?
2.) Facing issue in configuration...
Hello,
I am working on a beaconing application and I was wondering if it is possible to run the code beginning with system off mode and wake up the board with a button press...
Hi,
we are using a sensor which streams out buffered data to an ios or android app. If we face a disconnection the data gets buffered and send when reconnected.
But the...
Hi,
I am using customized nrf52 board with softdevice s132
I am trying to interface External Flash (MX25L64) using spi.so when ever i am trying to send any command /data...
