Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi!
I have been trying to observe the NRF_LOG_xxx output in my Eclipse console on debugging mode. However, nothing prints in the console (image 1).
I tried enabling...
Hi
Befor I used nRF51822 to transmit a packet per 5ms, payload length is 12. I can received 200 packets/s, Initialization settings are as follows
Device : nRF51822...
Dear all,
I have been struggling with updating my advertisement data package in SDK15. Using Jimmy Wongs's example ( https://github.com/jimmywong2003/nrf5-modify-device...
Hi,
to initialize the button properly
to trigger the push event on button push and the release event on button release, do I just have to change the button active state...
Hi there,
So I am trying to get a basic mesh setup between multiple Nordic Thingy 52's and no matter what I have tried i keep failing,
I have gone through the forums...
I have an Adafruit Bluefruit Feather nRF53832 board I am considering using and need to change the default serial baudrate from 115200 to 9600.
I am told that I can use the...
Hi:
I am using a shake sensor as an analog input wake-up system. The system is not system off. The analog input signal only generates an event to wake up turn on...
I am using the UART central, integrated with peer manager and UART peripheral application from the SDK 15.3 on our custom hardware. I have 2 centrals running exactly same...
Hello everyone.
I want to familiarize with The Power Profiler Kit. I've installed proper software and been trying to connect to the device but every time I receive the same...
Hello,
I am trying to load the ble_app_hrs example from sdk15 on to my external BMD-350 module, but I cannot seem to discover the module using nRFConnect. I am not using...
SDK:
nRF5_SDK_15.2.0_9412b96
Softdevice:
132_nrf52_6.1.0_softdevice.hex
Hi Sir,
I want add NUS function to ble_app_hrs_rscs_relay sample code and I add...
Hi,
I use a central with 4 peripherals connected with BLE protocol.
On the central, I use the radio notification interrupt. I would like to know which peripheral correspond...
Hi,
I have a problem in my application, i want to add scanning feature, but
When i call sd_ble_gap_scan_start () with these parameters it returns error (0x06) (with...
I am a begineer in Nordic trying to read voltage and current readings from ADC pin. I need to read both values in parallel, with known interval. So I need to use interrupts...
I am trying to use the LTE Sensor Gateway app to send Running Speed and Cadence Service Sample Application data loaded on a nRF52832. I have managed to get this two device...
