Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I'm under the impression that this piece of the given example is an interrupt handler. Am I correct? If yes, then there another snippet:
So, is there a while loop inside...
Hi All,
I am facing problem in my bootloader linking please see below
Linking target: binaries/bl/bootloader.out /tmp/cc9UGLw7.ltrans4.ltrans.o: In function `nrf_svc_handler_c...
How do you think - is there resources enough to add SPL (sound pressure level) measurement functionality into Nordic Thingy:52? Is microphone appropriate or may be external...
Hello, I'm using the example package Nordik_Mesh_V2_0_1 \ nrf5_SDK_for_Mesh_v2.0.1_src \ examples \ light_switch, and I would like to extend the number of servers from 4 to...
I'm trying to understand the cost differences, and pros and cons between:
A) creating a two chip solution - Using a BLE module - PLUS an second micro that runs my application...
I am in the process of trying to send live data from a nrf52 board over bluetooth to another nrf52 board using the example projects ble_app_uart_c and ble_app_uart. We are...
Hi,
I use SDK 12.3 to run experimental_ble_app_buttonless_dfu on nrf51822 after reference this blog , but still can not work.
It works fine with PCA10028 board.
I want...
hi :
i send characters of SPI master of 52DK to SPI slave of our target board(Nordic nRF52832), our target board use SDK v12 spis example. but spi slave event can not rececive...
I am using SDK 12.3.0 and S130 2.0.1.
In example ble_app_uart and ble_app_uart_c,
Central setting:
Peripheral setting:
Why it took so long to discover service...
Using the same connectivity firmware, a dfu update using nrfutil takes about four times as long as the same update using nrf connect. I have to setup dfu updating in a production...
Hi,
I am trying to communicate with a Wi-Fi module external to nRF52840 via UART. I am using the nrf_serial_read() API. I have tried different values for UART baud rate...
Hello, I am trying to broadcast a data among 2 receivers with a special ACK payload. I transmit and gather ACK with one receiver properly yet m_nrf_esb_mainstate locks in...
Hi,
I am trying to use Segger embedded studio for my project,
I get these errors:
Building ‘ble_app_uart_c_pca10028_s130’ from solution ‘ble_app_uart_c_pca10028_s130...
hello,BPROT does not work normally when i am debugging BPROT.
when i set CONFIG0 bit2 to 1,that is NRF_BPROT->CONFIG0 = 0x00000004,then i want to erase block 2(start address...
I am having a hard time turning ON semihosting. Here's my setup:
- Debugging is done via Eclipse GDB SEGGER J-Link Debugging with the Enable Semihosting checked and console...
