Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I am trying to use gcc to compile a c++ code for nRF52. I am using the TWI library and am getting the error below. Can anyone help me rewriting this macro so that it compiles...
Hello All,
I am using 32 pin nRF52810 chipset.
Crystal have two pin and it will work as in sch. (Xin and Xo)
when using Osc (which is an external clock generator) there...
Hello,
I'm trying to create a lightbulb custom HomeKit accessory by referring to the User Guide v1.7.1. I followed the exact same steps as described in the document for...
Hi,
* (i'am using sdk14.2 ans S140 V5.0.2)
i'am trying to inegrate a beacon application to my ble_uart example , so my purpose is to advertise ibeacon pachet format only...
We have some old stock of the nRF51822 pre 2014/8/20. Was there a change to the product around that time that would prevent us from using from using this stock?
Many th...
Hello,
I'm using FreeRTOS on nRF51 and I would like to use task notifications instead of semaphore to simply manage task's syncronization.
To test its operation mode,...
Hi, I just copied the antenna drawing by referencing the PCA10040 v1.1 and checking the white paper (λ/4 printed monopole antenna for 2.45 GHz) .
I didn't have much knowledge...
Hi,
How is the functionality of P0.21 in nRF52832? It is configured as RESET after turning on the device, right? Is there any way to change it in a way that that the chip...
Hello DevZone,
I am using a nRF52840 for project development.
To test SPI setting is correct or not, I am doing the loop-back test, I set the MISO and MOSI PIN according...
Hello,
I try to configure two nrf52832 devices work with payload of 200 bytes (data should be 200 bytes, not the all ble packet).
I took ble_app_uart_c peripheral and...
Hi all,
Using UART is confusing for me because I see various implementations in the documentation. There is a Serial library, then there is the UART driver and HAL. The...
I am trying to use the comparator to wake me up when a potentiometer is moved a certain amount.
Before I sleep I read the ADC value of the comparator and use this to set...
Hi,
I'm trying to set up the connectable/scannable advertising. I took the app_beacon example and changed advertising parameters.
My final set up is:
The ADV_INTERVAl...
I have the preprocessor define CONFIG_NFCT_PINS_AS_GPIOS in my code, and GPIO functionality for P0.09 and P0.10 are working just fine for me...
My issue is that even when...
