I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
NCS 2.5.2
Toolchain 2.5.1
NRF52840
Hi,
I'm currently power profiling our custom board. So far I've managed to get the current consumption quite low (6.5uA at 3V...
I am in a need to measure a battery level under a constant load. Rather than adding a custom electronics, I am considering using the radio. I believe there is a way of doing...
Hello,
I am attempting to use a J-Link or a FORTE programmer to interface with the debug port to upload a new binary/program to my board. Is this possible? I am trying to...
nRF52840
NCS 2.4.1 to NCS 2.6.1
My project is based on the coap_server example. When I ported it from NCS 2.4.1 to NCS 2.6.1, the network key and PSKC changed. All other...
SDK: v2.6.0. nRF5340 custom board
Hello I'm trying to do an static partitioning scheme using a pm_static.yml file and also I want to use NVS to store some data.
The...
Hi!
First off: I know the Cryptocell register interface is not officially supported, but I'm using it for learning purposes and I'd like to understand what's happening....
Hi, Using ncs v2.7 on the nrf9160, is there a data limit using MQTT to communicate with Azure IoT Hub per message? I'm trying to determine if I will need to chunk my telemetry...
We are developing a sleepy end device using the nRF52840, using light switch sample . The end device is connected to a Zigbee coordinator, also based on the nRF52840.When...
We are using a 5340 with a Skyworks 66112 FEM. Below is our hci_ipc.overlay file.
We are setting CONFIG_BT_CTLR_TX_PWR_ANTENNA =20. When we measure the output of the FEM...
I'd like to use playback feature of PWM. There is NRFX function for that: nrfx_pwm_complex_playback(). This function, like other NRFX drivers, needs appropriate instance structure...
My Win10 app - needs to connect to an NRF52 that is using the "NuS" Service - and I can't use the WinRT or dotNET.
In this post: https://devzone.nordicsemi.com/f/nordic...
Hello,
Thank you for reading my question. My company and I have developed a BLE device for use with windows computers based on the nrf52810. The device pairs with windows...
I'm building my zephyr project for nRF5340, using west.
However, each time I change my code and re-build to try it, my PC (which is pretty recent) takes around 40-50s just...
