Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
I have Six services in my project to be advertised and make available to the user at a time.
first I have faced problem while advertising two vendor UUID's.I solved...
Hi! I'm planning out the connection of a micro-SD card through SPI to the nrf52840. I'm reading through the documentation and when powering the nrf using a Li-Po through VDDH...
I am trying to add a bootloader to my application which I have currently running on an nrf51822 with SDK12.3.
The first problem was that the examples from SDK12.3 do not...
Sir,
I finally got success to measure the Coin Battery using a analog INPUT of NRF52832, AIN4
i am using ZEPHYR RTOS
I have to connect the BATTERY VDD to the AIN4. ...
Looking for Android logging utility where host processor on a Mobile device is interacting with nRF52810 over UART interface.
or Provide a stand alone logging utility that...
where can i search whta the mean about <type>,<result>,<datatype>,,<qos>,<retain>.....Etc.
EX: #XMQTTEVT: 4,0
I Don't know what these values represent
thanks
...
Hi,
We're using a 51422 with s130 to perform OTA DFU.
Both bases for bootloader and central are from sdk 12.2.
We have already implemented the older DFU (non-secure...
Hi,
I want to use the Code Profiling feature from Ozone with my nRF 52840 DK and the j-Trace Pro Cortex. Compiling and debugging my program works flawless inside Segger...
I am trying to figure out how to use the TX part of the BLE NUS Service to send a notification. Currently I am receiving data via the nus_data_handler, however because i will...
Hi, I just got my nRF5340 PDK and was wondering if it is possible to develop applications for the nRF5340 PDK in the Keil IDE?
I have been reading on the site and trough...
Normally with Segger Embedded Studio if you want to do a command-line build you use embuild.exe instead of emstudio.exe and away you go.
However, the NRF Connect/Zephyr...
Hi
We searched a lot of stuff regarding FOTA update in nRF52840DK using Lwm2m and coap protocol. But we could not get help in the right direction. We could not find any...
Hi,
We are using today SDK 15.0 and are upgrading to SDK 17.0 for development of our system.
In our application, we use BLE communication.
While comparing SDK_config...