GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi,
I'm using latest master branch of nRF Connect SDK and pre-released modem FW 1.1.2 which is including ANT->AUX switching. I'm developing a firmware for a custom board...
Hello,
I notice that Thread examples with Softdevice (nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b) works fine for a PCA10056 but not on a PCA10059. When I had tried...
I am using nrf52832. I have one led connected to the gpio 25 through the active low condition.
i am trying to configure gpio 25 using this " nrf_gpio_cfg_pin_output(25);...
Hi, what is the impedance of the nRFM9160 GSM antenna?
I'm asking because I'm in the process of verifying the tuning on an antenna + LNA circuit. We will most likely tune...
I am using nrf52832. I am making custom board file .I am little bit confused which function are used for set the pin as output or input.
__STATIC_INLINE void nrf_gpio_cfg_output...
Hi All,
from below post, I found that in SDK11, bootloader code uses NRF_UICR->CUSTOMER[0] register for device type and revision verification so application should not use...
Hi
This is Joe. I would like to ask questions about implementing BLE bonding.
SDK: 16.0.0 (nRF5SDK160098a08e2)
Projects: The base project I start with is NUS example...
Hello,
I am trying to develop BLE custom board. It's my first time dealing with Nordic MCUs and RF. I want to understand if I am doing it all correct. Here is a piece of...
Hi,
In the I2C communication,the nRF52840 SoC is master, the sensor SCD 30 is slave. The sensor SCD 30 needs the clock stretching period, the period time is 12ms or 150ms...
Hello,
I have a general question for you.
When we develop an application from one of your examples and then you put online a new version of your SDK, do you have any advice...
Hello, I am using the nrf9160 DK and connected it with a SIM card of a local provider. The SIM card is able to connect to the LTE network and NB-IoT.
For researches I only...
Hi, I am developing a multi-link central using NRF52832 and SDK 16. I have implemented the scanning part and NRF_BLE_SCAN_SCAN_DURATION = 0. I am using address filter for...
Hi Nordic Team,
I know there are many tickets raised concerning this error 133. It is a quite generic issue with Android devices of various android versions and I have gone...
Hi, I have a problem find bluetooth device on more android phones after them unpair.
First time phones find device and connect but after unpair phone not find devices. ...
