Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
My I2C communication...
I desgined a PCB based on the nRF52840 module and led out the SWDIO and SWDCLK pins to Micro USB.
I used jlink v9 and connected three pins in SWD download mode. The SWDIO...
We have developed a custom board based on nrf52810 SoC (package : QFN32) , after following the guides on the forum we tried to run the example ble_app_uart(pa10040e) from...
Hello, I couldn't find any examples of SPI usage with nrf connect sdk, where can I find them?
At the beginning I want to do pretty simple thing - just send array of bytes...
Hi noridc,
I am using the sdk 15.03, s140 and the nrf52840.
I used as a reference the ble_app_interactive experimental example and the ble_central/ble_app_hrs_c. My...
Dear Community, good morning
I am working in a design that do not use USB port. If VBUS pin is left floating could it cause any issues to nRF52840.
Best regards,
Hello, guys!
I have some questions concerning GPS receiver inside nRF9160. You say in your documentation that GPS receiver supports L1 C/A reception - link .
There are...
What's the easiest way to view all logs and error messages using USB serial connection app like putty, on the nRF52840 dongle?
What drivers and functions do I need to enable...
What level of risk is involved with brownouts for the modem? We have seen some modems in the past which have bricked themselves when a brownout has occurred when performing...
Hello, I want to inquire about the functionality of nRF52833-DK if I want to communicate between transmitter and receiver for locating position of receiver using BLE (Bluetooth...
Hello ,
I am interfacing the nRF52832 with winband spi flash . I can able to read the device manufacture id but i couldn't able to read the data from the device . I am getting...
Hi,
I am using the nRF52840 to sample some channel.
I am using the nRF5SDK160098a08e2 for that and based on the saadc example.
These are the results for my tests....
Hi there,
I've been unable to find a good example of what settings are required specifically to ensure that a characteristic's value can only be read and notified in an...
I have a question regarding the nRF Toolbox App v5.0.2 on iOS 14.1 and the Cycling Speed and Cadence demo app. It appears to be that the km/h calculation based on the CSCS...
Hi
I have created 4 threads in nRF9160 application, I have to go to sleep if none of the thread is running.
For this how do I check whether the created threads are running...
