Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Please refer to the image below:(If you cannot see the image, link here: postimg.org/.../)
I'm not entirely sure what this pin does, does it output reference voltage...
Why can't I breakpoint or step blinky, using kiel MDK lite?
Comment --- I suggest Nordic do videos or provide exact steps for how to setup-run the base example (like Blinky...
I've been having a very difficult time debugging this issue. I've modified the bootloader_secure example and have it working on the dev kit using the 330 Softdevice. It works...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi Nordic,
My application does the following:
Timer 2 takes care of controlling a shift register (CLK and DATA)
Timer 1 takes care of polling data from sensor...
Hi!
I am in the process of upgrading a quite large project from SDK 8.1 to SDK 12.2. It uses the nRF52 DK, PCA10028. I still use the toolchain I stated with, including...
Following this tutorial , but for pca10028 , softdevice s130 instead. I'm on Linux.
Under "Running", when I press Ctrl + F5 , I get the error s130_nrf51_2.0.1_softdevice...
Hi,
I try to modifie ble_multilink example et send more than one data,
here is my main code code :
static uint8_t test[4] = {0x41, 0x42, 0x43, 0x44};
static...
Hello,
SPIS is adding a 350uA from 80uA baseline running current. I would like some tips and advise on improving this. Thanks!!!
The baseline operation consists of:...
I am using eclipse as IDE , but when i build ble_app_hrs example it's getting an error ../../../../../../components/ble/ble_advertising/ble_advertising.c:195: undefined reference...
I have a 32u4 Feather but don't get the right support from Adafruit to create my own Profile. I have downloaded Nordic's android app and can see all the characteristics on...
Hi.
I'm trying to enable and disable softdevice repeatedely.
In my code, softdevice is firstly enabled then advertising properly.
After some seconds, softdevice is disabled...
Hi,
I used the ble_peripheral and ble_central example and I send messages from one to the other.
Know I need to do the same with multilink.
I managed to connect ble_multilink_central...
hi dear Engineers!
the questions is it possible to use RX RF reciever to estimate the average BW RF signal input power like I do it in Semtech 433/868 RF SoC to make desicion...
hi, all
my nrf52832 can not run good when download the program into the flash, and can not run good in debug session mode without breakpoint ， but if I add one breakpoint...
